亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

Lifting cylinder Sold to Italy

Release time:2023-11-17 13:21:24 Hits: Current position: Home > News

This article mainly introduces:

Italy hydraulic cylinder,Lifting cylinder manufacturer,Lifting cylinder

Italy Lifting cylinder

(Italy Lifting cylinder,produced by Hengyu Group)

Lifting cylinder are widely used in Italy,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed Lifting cylinder for customers from Italy.

Introduction to Lifting cylinder:

If the seal of the Lifting cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the Lifting cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The quality of the Lifting cylinder can not be ignored in the purchase of the Lifting cylinder. The Lifting cylinder is the main component of the Lifting cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Lifting cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of Lifting cylinder is deep hole processing, which has always troubled the processing personnel.

The internal leakage of the Lifting cylinder should be prevented when the Lifting cylinder is used. The internal leakage of Lifting cylinder includes the leakage caused by excessive wear of Lifting cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

Answers to some questions about Lifting cylinder:

PLC+ inverter + motor + pump + solenoid valve + cylinder combination, can control the accuracy of cylinder position?
In the case of extremely high accuracy requirements, you can not, please consider a few problems: 1, hydraulic oil can be compressed, it is elastic like a spring. Therefore, in the general hydraulic servo system, the valve control is far more accurate than the pump control. Because the valve can be installed very close to the hydraulic cylinder, or even installed on the hydraulic cylinder, but the pump must go through the tubing and then into the hydraulic cylinder, there is a long distance, which greatly reduces the rigidity of the system and increases the difficulty of control. 2, the quantitative pump is first of all leaking, and there is 10%-20% flow pulsation. Secondly, and more unfortunately, the leakage of the pump is related to the pressure and is non-linear.

What is the clearance between the cylinder and the piston?
The gap between the cylinder and the piston in the radius is generally 40 wires, that is, about 0.4mm, and the gap of the cylinder with different diameters will be slightly different. Generally, the inner diameter of the cylinder is larger than the outer diameter of the piston, so as to prevent the friction between the outer surface and the inner surface of the cylinder during the operation of the piston. In order to ensure that the cylinder has a rod cavity and a rodless cavity seal, a sealing device, that is, a sealing ring, is installed on the outer surface of the piston. The sealing ring form is not exactly the same, the O-type sealing ring is generally used under low pressure, and the lip sealing ring is used under high pressure. At the same time, the outer circle of the piston is also equipped with a dust ring and a wear ring. As long as the cylinder seal fails, all the internal seals should be replaced.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
尤物AV无码国产在线看| 日韩午夜经典福利| 为什么搜索不到裸体| 小嫩骚逼操死你视频| 中文字幕乱码一区二区三区麻豆| 91久国产在线观看| 日韩成人伦理片在线观看| 日韩欧美一区二三区风间由美| 白丝袜子宫啊啊啊不要了| 色一情一交一乱一区二区| 九九视频免费在线观看| 国产 日韩 亚洲 一区| 淫荡淫水逼操烂视频| 精品日韩欧美精品日韩| 束缚久久久久久免费高潮| 96精品久久久久久蜜臀浪| 日本熟人妻中文字幕在线| 亚洲免费福利视频| 久久一区二区三区精华液介绍| 妺妺坐在我腿上下面好湿| 任你橹在线久久精品9| 黑人大屌爆操骚货| 欧美一区二区高清视频在线观看| 成人高清在线播放一区二区三区| 娇嫩的被两根粗大的np| 少妇无套带白浆嗯呢啊污| 亚洲欧美国产原创一区二区三区| 天堂丝袜人妻中文字幕在线| 美国大鸡巴操逼视频| 春宵福利导航91| 亚洲午夜av一区二区三区| 女同舔我下面直流水| 亚洲高清中文字幕一区二区三区| 国产精选三级在线观看| 日韩精品高清在线| 美性中文网中文字幕91| 99久久国产综合精品女| 日本精品高清在线观看| 日本亚洲欧洲一区二区| 午夜福利在线观看aaa| 市长含着秘书的奶头|