亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo hydraulic cylinder Sold to Oman

Release time:2023-11-17 13:21:23 Hits: Current position: Home > News

This article mainly introduces:

Oman hydraulic cylinder,servo hydraulic cylinder manufacturer,servo hydraulic cylinder

Oman servo hydraulic cylinder

(Oman servo hydraulic cylinder,produced by Hebei Hengyu company)

servo hydraulic cylinder are widely used in Oman,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed servo hydraulic cylinder for customers from Oman.

Introduction to servo hydraulic cylinder:

The assembly work of the servo hydraulic cylinder has a great impact on the quality of the servo hydraulic cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

In order to ensure the service life of the servo hydraulic cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the servo hydraulic cylinder, causing damage to the seal and causing leakage in the servo hydraulic cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

Before the servo hydraulic cylinder is removed, the system should be unloaded, the loop pressure is zero, the oil source should be cut off, and the oil port should be blocked after the oil port distribution pipe is loosened.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the servo hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

Answers to some questions about servo hydraulic cylinder:

Need a hydraulic cylinder, vertical upward 10 seconds to lift 20 tons of weight up 2 meters, how large cylinder and rod, how much pressure to use the plunger pump and how big?
The first thing to determine the system pressure, let's say 25 mpa, can take into account cost and performance. 1 Cylinder area 20000/250=80 square cm cylinder diameter (80/3.14) squared x2=200 mm 2 cylinder volume 80x200=16000 ml =16 L 3 Required pump flow 16x60/10=96 L/min 4 Power 96x25/55=43 kW 45 kW motor is available.

Why can't the hydraulic cylinder be pulled back after pushing to the limit?
May be long-term use to the limit position, resulting in serious wear caused! The solution is to add the stroke switch or disassemble and add gaskets before and after the piston.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品999午夜激情| 爆乳喷奶水无码正在播放| 思思夜免费公开视频| 国产色哟哟精选在线播放| 白虎嫩穴抠逼高潮| 日韩素人精品亚洲热一区| 精品国产Av无码久久久一区二区| 69国产成人综合久久精| 日本免费精品一区二区三区四区| 男男大鸡巴操小屁眼视频| 免费看看小骚逼逼| 色婷婷五月综合久久| 啊啊好想被大鸡巴操视频| 巨屌抽插舔阴视频| 97人妻精品一区二区三区视频| aaa啊啊啊黄片| 99精品一级欧美片免费| 色哟哟精品视频一区二区| 男生操女生无马赛克免费| 国产激情内射免费精品| 久久精品国产亚洲av伦理| 男插女逼啪啪啪软件| 一区二区国产欧美日韩无| 97人人澡人人爽人人揉| 巨屌抽插舔阴视频| 一区二区国产欧美日韩无| 亚洲一级片在线播放| 欧美大鸡巴操大骚逼| 伊人久久久久久久久香港| 久久综合色伊人九色91| 少妇勾搭外卖员在线观看| 亚洲综合极品香蕉久久网| 毛片日产av一区二区三区四区| 黄色片视频1024| 国产试看精品无码中| 妺妺坐在我腿上下面好湿| 青娱乐极品视觉导航| 国产乱色国产精品免费播放| 国产精品熟女视频播放| 国产裸模大尺度私拍视频| 搬开女人下面使劲插视频|