亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

single rack cylinder Sold to Burma

Release time:2023-12-08 14:41:24 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder

Burma single rack cylinder

(Burma single rack cylinder,produced by Hengyu Hydraulic Cylinder Factory)

single rack cylinder are widely used in Burma,because of no need for deceleration device,long service life,smooth movement.So our company has designed single rack cylinder for customers from Burma.

Introduction to single rack cylinder:

The cavitation of the single rack cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the single rack cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

Classification of single rack cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

The viscosity of the working oil used in the single rack cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

The piston seal of the single rack cylinder is the main element to prevent leakage in the single rack cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

Answers to some questions about single rack cylinder:

What is the reason why the hydraulic cylinder is not good at lifting?
There may be several situations 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

How is the hydraulic cylinder tempered?
The purpose of the tempering treatment is to make the piston rod have comprehensive mechanical properties of strength, hardness, plasticity and toughness, and the internal structure is uniform and fine tempered sorbite, so as to prepare the organization for subsequent surface quenching. The length of the long cylinder piston rod is 3800-4200, and the diameter is Φ90-Φ110mm, so its heating equipment uses a 150KW well resistance furnace or 600KW suspension continuous resistance heating furnace, and the temperature is controlled by two areas. Heat treatment process parameters: in the shaft furnace, a furnace is suspended with 4 pieces, the quenching heating temperature is 830±10℃, and after holding heat for 160min, it is divided into two times for quenching, and two pieces are quenched each time, and the circulating cooling water is used for cooling.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲男人的天堂2023| 欧美黑屌操B内射冒白浆| 淫荡扣逼骚逼视频| 嗯啊好大好想要视频| 无码av一区二区大桥久未| 欧美一区二区三区久久国产精品| 国产精品毛片无遮挡高清| 我想看操小嫩逼大片| 小穴抽插流水视频| 美女荒郊野外找男人靠逼| 亚洲国产成久久成人综合一区| 日韩欧美一区二区三区在线视频| 久久国产高清波多野结衣| 美女被操的流水AV| 美女麻豆颜色光屁股眼子| 欧美一区二区三区四公司| 市长含着秘书的奶头| 二次元男生操女生屁眼爽| 大鸡吧插美女嫩逼| 我和两个老师的浮乱生活| 日韩成人伦理片在线观看| 色噜噜人妻丝袜中文字幕| AV天堂手机福利网| 色999日韩自偷自拍美女| 操小骚逼高潮视频| 国产精品免费第一区二区| 几把日逼嗯嗯视频| 久久综合久久久久综合大| 92婷婷伊人久久精品一区二区| 亚洲AV无码一区二区三区系列| 美女呻吟翘臀后进爆白浆| 男人把鸡巴插入女人| 在线免费看污视频| 久久国产老熟女老女人| 美女人的逼免费观看| 欧美猛男一区二区三区快播| 欧美大鸡巴捅骚逼吃| 91久久愉拍愉拍国产一区| 亚洲国产一区二区不卡在线资源| 大鸡巴插我在线观看| 国产午夜精品美女视频露脸|