亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

extra high pressure cylinder Sold to Canada

Release time:2023-12-08 14:41:16 Hits: Current position: Home > News

This article mainly introduces:

Canada hydraulic cylinder,extra high pressure cylinder manufacturer,extra high pressure cylinder

Canada extra high pressure cylinder

(Canada extra high pressure cylinder,produced by Hengyu Hydraulic Co., Ltd)

extra high pressure cylinder are widely used in Canada,because of excellent fatigue and impact resistance,no need for deceleration device,high work efficiency.So our company has designed extra high pressure cylinder for customers from Canada.

Introduction to extra high pressure cylinder:

The scar on the sliding surface of the extra high pressure cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the extra high pressure cylinder wall. Therefore, before installation, these scars must be fully repaired.

If the extra high pressure cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the extra high pressure cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow extra high pressure cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the extra high pressure cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the extra high pressure cylinder includes the leakage caused by excessive wear of the extra high pressure cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and extra high pressure cylinder, and the phenomenon of "pulling the extra high pressure cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

If the seal of the extra high pressure cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and extra high pressure cylinder, and the phenomenon of "pulling the extra high pressure cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

The repair method of extra high pressure cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about extra high pressure cylinder:

Are hydraulic cylinders divided into oil cylinders and water cylinders? What's the difference between the two types?
There are oil cylinders and water cylinders. The two cylinders are used in different environments. Oil cylinders are generally used in places where there is less demand for media, which is our most common hydraulic cylinders. Water cylinders are mainly used for large tonnage presses. Because the equipment is too large, the use of hydraulic oil will cause a relatively large waste. However, water is not pure water, there are oil-in-water emulsion and water-in-oil emulsion. Water has another benefit: it's flame retardant. It is especially suitable for some flammable and explosive occasions. Or with water glycol. The use of pure water is very little, mainly because the seal is not good and easy to rust.

How to set the stroke of the cylinder?
Self-design should be based on product demand and practical application. The stroke of standard cylinder depends on the parameters the customer requires. The hydraulic cylinder is a linear motion actuator whose output force is proportional to the effective area of the piston and the pressure difference on both sides. Its function is to convert hydraulic energy into mechanical energy. The input of the hydraulic cylinder is the flow rate and pressure of the fluid, and the output is the speed and force of the linear motion. The piston of the hydraulic cylinder can complete the linear reciprocating movement, and the linear displacement of the output is limited. Hydraulic cylinder is an energy conversion device that converts hydraulic energy into mechanical energy of reciprocating linear motion. The hydraulic cylinder is basically composed of cylinder body, cylinder head, piston and piston rod, sealing device, buffer device and exhaust device.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲精品国产人久久| 韩国年轻的母亲在线观看| 老司机午夜精品视频无码| 日韩人妻精品一区二区三区99| 日本欧美一区二区三区| 开心五月播五月亚洲第一| 亚洲大尺度无码无码专线一区| 中文字幕国产精品一区二区三区| 亚洲日韩国产欧美久久久| 成人男女做爰免费视频网| 亚洲中文字幕二区不卡| 中文字幕一高清免费视频| 找个日韩操逼的看看| 色男人天堂亚洲男人天堂| 国产一区精品在线| 操世界最美丽的逼片| 亚洲人成在线不卡网| 日韩美女一区二区三区香蕉视频| 操老女人大逼视频| 欧亚洲嫩模精品一区三区| 九九在线精品亚洲国产| 亚洲AV无码一区二区三区天堂古| 亚洲精品精品精国产| 欧美尤物操逼毛茸茸真爽| 非洲大鸡巴操逼黄色录像| 欧美一区二区三区色婷婷月色| 亚洲一区二区三区四区国产| 欧美日韩一区精品一区精品| 色男人天堂亚洲男人天堂| 激情五月六月婷婷俺来也| 日本a国产精品久久久久| 日本免费一区二区在线| 精品日本一区二区三区视频播放| 国产伦精品一区二区三区视频抖音| 欧美成人3p视频| 麻豆91精品96久久久| 日韩av一区二区高清不卡| 国产高清一区二区三区四区色| 亚洲国产AV精品一区二区色欲| 一级美女插逼百度| 黑人大鸡巴双插美女|