亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo cylinder Sold to Poland

Release time:2023-11-20 09:49:45 Hits: Current position: Home > News

This article mainly introduces:

Poland hydraulic cylinder,servo cylinder manufacturer,servo cylinder

Poland servo cylinder

(Poland servo cylinder,produced by Hebei Hengyu company)

servo cylinder are widely used in Poland,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed servo cylinder for customers from Poland.

Introduction to servo cylinder:

The wear of the hard chromium plating layer of the servo cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

How to repair the servo cylinder body when it is damaged: When the servo cylinder has trace deformation and shallow tensile marks, the servo cylinder is repaired by strong honing process. The heavy honing process can repair servo cylinders up to 2.5 times out of tolerance than the original tolerance. It honed the parts with excessive size or shape error through a powerful honing machine, so that the overall size, shape tolerance and roughness of the servo cylinder can meet the technical requirements.

The definition of the minimum stable speed refers to the minimum movement speed of the servo cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the servo cylinder that undertakes different work has different requirements for the minimum stable speed.

servo cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the servo cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Answers to some questions about servo cylinder:

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

Why is the hydraulic cylinder of the larger excavator arm upside down?
The weight of the excavating arm of a large excavator will be very heavy, and an oil cylinder has two cavities, one is a rod cavity, and the other is a rodless cavity. The lifting force of the excavator is the product of the ortho-projection area of the piston rod cavity by the oil pressure, so the strength of the rodless cavity is much greater than that of the rod cavity. And the parallel bars with the piston rod facing down are also conducive to assembly and future maintenance. So a large excavator has to keep the cylinder facing down.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
插女人下面高潮视频| 手机成人三级a在线观看| 在线观看日韩欧美| 亚洲av一区二区在线看| 91kaobi视频在线| 美女主播被操流水| 俩男人插下面的视频| 日韩欧美一区二三区风间由美| 亚洲精品美女久久久| 午夜精品在线视频| ai换脸久久一区二区亚洲av| 欧美va精品亚洲va精品| 白色紧身裤无码系列在线| 骚狐狸免费在线观看视频| 伊人久久亚洲婷婷综合久久| 欧美人与性动交b欧美精品| 久久久久久久 亚洲精品| 尤物性生活午夜在线视频| 操女人大逼视频下载| 欧美亚洲熟妇视频在线观看| 毛片日产av一区二区三区四区| 日韩av一区二区高清不卡| 国产精品三二一免费| 欧美日韩久久久一区二区三区| 久久久久久高清无码视频| 国产乱色国产精品免费播放| 成人av大全免费一区二区三区| 午夜十八禁福利亚洲一区二区| 成人 在线 欧美 日韩| 天天天天天干夜夜夜夜夜操| 日韩午夜免费av在线| 丁香婷婷色婷婷粗大| 亚洲综合色88综合天堂| 精品日本一区二区三区视频播放| 亚洲国产嫩草18久久久| 巨屌抽插舔阴视频| 午夜十八禁福利亚洲一区二区| 看人妻仑乱A级毛片| 热精品韩国毛久久久久久| 麻豆视频一级片在线观看| 成人久久久久久蜜桃免费|