亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

filling machine cylinder Sold to Bahrain

Release time:2023-11-20 09:49:44 Hits: Current position: Home > News

This article mainly introduces:

Bahrain hydraulic cylinder,filling machine cylinder manufacturer,filling machine cylinder

Bahrain filling machine cylinder

(Bahrain filling machine cylinder,produced by Hebei Hengyu company)

filling machine cylinder are widely used in Bahrain,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed filling machine cylinder for customers from Bahrain.

Introduction to filling machine cylinder:

The internal leakage of the filling machine cylinder should be prevented when the filling machine cylinder is used. The internal leakage of filling machine cylinder includes the leakage caused by excessive wear of filling machine cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the filling machine cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

Because of the slightly complex structure of the buffer filling machine cylinder, sometimes there will be problems, such as when the filling machine cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

filling machine cylinder piston rod material introduction: In general, we use 45 steel to produce filling machine cylinder piston rod. It has a large impact force when it is used, and some good performance steel are also used in the heavy load transmission. In order to have enough work intensity when using, and can ensure normal use, this is still more critical to have a detailed understanding of the material.

Answers to some questions about filling machine cylinder:

Classification and application of cylinders.
Hydraulic cylinder is divided into single acting hydraulic cylinder, double acting cylinder, combined hydraulic cylinder, swing hydraulic cylinder. Single acting cylinder is divided into plunger type hydraulic cylinder, single piston rod hydraulic cylinder, double piston rod hydraulic cylinder, telescopic hydraulic cylinder. Plunger type hydraulic cylinder: the plunger moves only in one direction, and the return stroke is to push the plunger back using its own weight or load. Single piston rod hydraulic cylinder: The piston moves only in one direction, and the return stroke is to push the plunger back using dead weight or load. Double piston rod hydraulic cylinder: both sides of the piston are equipped with piston rods, and pressure oil can only be supplied to one side of the piston. The return stroke usually uses spring force, gravity or external force. Telescopic hydraulic cylinder: It obtains long stroke with short cylinder. The hydraulic oil is pushed out from large to small section by section, and the external force is reduced from small to large.

Structural characteristics of the plunger cylinder? (1) The plunger hydraulic cylinder is a single-acting hydraulic cylinder, which can only move in one direction by hydraulic pressure, and the return trip of the plunger depends on other external forces or the weight of the plunger; (2) The plunger is only supported by the cylinder liner and is not in contact with the cylinder liner, so the cylinder liner is easy to process, so it is suitable for long stroke hydraulic cylinder; (3) the total pressure of the plunger during work, so it must have sufficient stiffness; (4) The weight of the plunger is often large, and it is easy to sag due to its own weight when placed horizontally, resulting in wear of the seals and guide side, so its vertical use is more favorable.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
aaa无码偷拍亚洲| 日韩欧美一区二区三区在线视频| 国产美女裸体视频全免费| 日韩精品高清在线| 男生操女生无马赛克免费| 99热这里只有精品98| 我最爱操女人的骚逼| 看一下日本人插逼逼洞视频| 老头鸡巴操老太骚逼| avtt天堂网先锋伦理| 永久性日韩无码视频| 久久高清中文字幕第一页| 欧美日韩久久一区二区三区| 中文字幕日韩亚洲| 日韩av一区二区三区激情在线| 黄色视频力肏女人| 成人黄色精品久久app| 少妇毛片一区二区三区免费视频| 男人操女人下面国产剧情| 亚洲精品自拍偷拍第一页| 狗狗大鸡巴狂操美女| 国产成人无码AV一区二区三区| 亚洲 欧美 精品 高清| 波多野结衣浴尿解禁在线| 一级e片在线观看| 国产成人无码AV一区二区三区| 久久久久久久 亚洲精品| 亚洲高清中文字幕一区二区三区| 国产女做a爱全免费视频| 2021最新热播国产一区二区| 亚洲日韩不卡一区二区三区| 女人被男人操到高潮视频| 嗯嗯好硬好大啊老公| 色999日韩自偷自拍美女| 中文字幕一高清免费视频| 伊人久久亚洲婷婷综合久久| 国产熟女50岁一区二区| 两人爽爽爽无码免费视频| 欧美大鸡巴操大骚逼| 8050午夜三级的全黄| 亚洲国产综合精品 在线 一区|