亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push plate cylinder Sold to Nigeria

Release time:2023-11-13 11:19:42 Hits: Current position: Home > News

This article mainly introduces:

Nigeria hydraulic cylinder,push plate cylinder manufacturer,push plate cylinder

Nigeria push plate cylinder

(Nigeria push plate cylinder,produced by Hengyu Hydraulic Co., Ltd)

push plate cylinder are widely used in Nigeria,because of no need for deceleration device,long service life,smooth movement.So our company has designed push plate cylinder for customers from Nigeria.

Introduction to push plate cylinder:

Factors that should be considered when selecting the oil seal in the push plate cylinder: some specific factors should be taken into account when selecting the oil seal in the push plate cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: push plate cylinder diameter, piston rod diameter, piston rod and piston groove size, push plate cylinder working pressure, push plate cylinder movement speed, hydraulic system oil temperature and push plate cylinder working environment.

If the piston rod and push plate cylinder are stuck or the push plate cylinder is blocked, at this time, no matter how to operate, the push plate cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the push plate cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Disassembly push plate cylinder: When disassembly push plate cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the push plate cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the push plate cylinder.

push plate cylinder body inspection: The inner surface of the push plate cylinder and the piston seal are the main factors causing the leakage in the push plate cylinder, if the push plate cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the push plate cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

Answers to some questions about push plate cylinder:

How to calculate the inner diameter of the hydraulic cylinder?
These two parameters need the following information to decide: 1, pump displacement, speed (to get the actual output flow of the pump) 2, three and time requirements (lift time, drop time takes a few seconds) and then view the close cylinder series according to the results. Select the right cylinder.

How to achieve hydraulic cylinder self-locking?
Hydraulic cylinder self-locking is divided into oil self-locking and mechanical self-locking. The oil self-locking is equipped with a valve to maintain pressure, so that the hydraulic oil of the cylinder does not return to the tank, and the oil chamber of the cylinder is filled with a certain pressure of oil. However, this pressure holding self-locking is not very safe and reliable, and the plunger will slowly return if there is a leak. Mechanical self-locking is to install a nut on the plunger of the cylinder, and when the cylinder rises to the required position, the nut on the cylinder plunger is rotated to the end, and the cylinder block is in contact, so that the plunger will be fixed to the required height. When it is necessary to relieve the pressure, screw the nut on again and let the plunger return to the position. This kind of cylinder has a special name, called self-locking hydraulic cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
777米奇在线视频无码| 亚洲av 又黄又爽十大| 亚洲欧洲日本精品| 免费男人和女人黄片| 亚洲高清中文字幕一区二区三区| 大吊肏子宫在线观看| 欧美日韩一级视频| 鸡巴操美女小穴羞羞视频| 操大美女逼射精视频| 草草久性色av综合av| 中文字幕在线精品的视频| 九九在线视频热线视频精选| 精华欧美一区二区久久久| 97超级免费视频在线观看| 挺进绝色邻居的紧窄小肉| 无码中文字幕免费一区二区三区| 思思夜免费公开视频| 国产精品一区二区三区色噜噜| 亚洲乱熟女一区二区三区| 午夜精品福利一区二区三区蜜桃p| 99精品一级欧美片免费| 青青视频在线人视频在线| 亚洲av 又黄又爽十大| 欧美一级淫片免费播放口| 国产熟女50岁一区二区| 国产福利一区二区精品秒拍| 嗯嗯好硬好大啊老公| 亚洲综合网伊人中文| 国产伦精品一区二区三区视频抖音| 骚穴 操我 视频| 一区二区国产欧美日韩无| 在线免费看污视频| 国产精品免费第一区二区| 国产免费无码一区二区视频无码| 99国产精品一区二区| 欧美一区二区三区身体| 青春草在线视频观看| 小骚货舔小骚逼视频| 高清国产一区二区| 亚洲一区二区三区大胆视频| 久久69精品久久久久免|