亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

land leveller hydraulic cylinder Sold to Uzbekistan

Release time:2023-11-13 11:19:42 Hits: Current position: Home > News

This article mainly introduces:

Uzbekistan hydraulic cylinder,land leveller hydraulic cylinder manufacturer,land leveller hydraulic cylinder

Uzbekistan land leveller hydraulic cylinder

(Uzbekistan land leveller hydraulic cylinder,produced by Hengyu Group)

land leveller hydraulic cylinder are widely used in Uzbekistan,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed land leveller hydraulic cylinder for customers from Uzbekistan.

Introduction to land leveller hydraulic cylinder:

How to determine the working pressure of the land leveller hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, land leveller hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

The scar on the sliding surface of the land leveller hydraulic cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the land leveller hydraulic cylinder wall. Therefore, before installation, these scars must be fully repaired.

The method of sleeve land leveller hydraulic cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the land leveller hydraulic cylinder can be significantly improved by rolling in the finishing of the inner holes of the land leveller hydraulic cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

Because of the slightly complex structure of the buffer land leveller hydraulic cylinder, sometimes there will be problems, such as when the land leveller hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

Answers to some questions about land leveller hydraulic cylinder:

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

How to calculate the hydraulic cylinder pressure, how much pressure can put up how much weight?
There is a formula for air pressure, hydraulic pressure, water pressure: F=P×S type: f-cylinder or hydraulic cylinder output, unit is Newton (N) P- pressure, unit is Mpa S- effective area, unit is square millimeter (mm2), note: is the effective area, in the hydraulic cylinder to subtract the cross-sectional area of the piston rod.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产91视频观看| 欧美 日韩 国产 自拍| 亚洲欧美日韩精品一区二区| 精品一区二区av天堂色偷偷| 韩国女主播一区二区视频| 亚洲男人的天堂2021| 国产亚洲欧美中文日韩| 日韩免费一级a毛片在线播放一级| 综合伊人久久在一二三区| 国产精品你懂的在线资源| 区国产精品搜索视频| 另类亚洲欧美专区第一页| 亚洲国产精品一区亚洲国产| 国产蜜月精品高清一区二区三区| 久久69精品久久久久免| 一区二区三区av精品| 国产精品熟女一区二区三区久久夜| 亚洲乱码专区一区二区三区四区| 久久久久黑人强伦姧人妻| 被春药女高潮抽搐喷水视频| 精华欧美一区二区久久久| 精品v欧洲高清欧美| 欧美一区二区高清视频在线观看| 麻豆91精品96久久久| 免费人成再在线观看| 玩弄邻居少妇呻吟11p| 黑人大吊性交啪啪啪| 强伦人妻一区二区三区视频18| 九九热在线精品免费看| 欧美一级特黄大片在线看| 国产老妇伦国产熟女91| 国产精品538一区二区在线| 精品免费福利片国产| 啊灬啊别停灬用力啊男男在线观看| 天堂丝袜人妻中文字幕在线| 新视觉亚洲三区二区一区理伦| 少妇精品久久久一区二区免费| 日韩美女叉B视频| 97超级免费视频在线观看| 日韩精品诱惑一区?区三区| 大吊肏子宫在线观看|