亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic steering cylinder Sold to Portugal

Release time:2023-11-13 11:19:37 Hits: Current position: Home > News

This article mainly introduces:

Portugal hydraulic cylinder,hydraulic steering cylinder manufacturer,hydraulic steering cylinder

Portugal hydraulic steering cylinder

(Portugal hydraulic steering cylinder,produced by Hebei Hengyu company)

hydraulic steering cylinder are widely used in Portugal,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed hydraulic steering cylinder for customers from Portugal.

Introduction to hydraulic steering cylinder:

When the hydraulic steering cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

hydraulic steering cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the hydraulic steering cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

In order to ensure the service life of the hydraulic steering cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

Answers to some questions about hydraulic steering cylinder:

How long can a hydraulic cylinder work continuously?
If the maintenance is good, the service life can be extended a lot. The life of the cylinder is related to the structure of the cylinder, working pressure, stress state, hydraulic oil cleanliness, oil temperature control, maintenance and preventive measures. For example, the cylinder structure, the inner wall of the cylinder has quilting, rolling, chrome plating and other methods, the sealing parts have polyurethane rings, glay rings, metal sealing rings, etc., different combinations, the life difference is dozens of times. Metallurgical system is a typical cylinder application, in 24 hours of work, a year or more can not be shut down, in the middle of continuous work.

What is a constant velocity cylinder? What is the difference between hydraulic cylinder and constant velocity cylinder?
The constant speed cylinder should be the same as the speed of the piston rod extension and withdrawal cylinder is called the constant speed cylinder. The difference between it and the ordinary hydraulic cylinder is that the ordinary hydraulic cylinder only has a piston rod extended out, and the general extension speed is slow and the recovery speed is fast, because of the relationship between the effective area. Effective area of piston chamber > Effective area of piston rod chamber. The effective area on both sides of the constant speed cylinder is the same, because there are piston rods sticking out at both ends. The application of constant speed cylinder is most common in grinding machines.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产亚洲一区二区手机在线观看| 国产熟女视频一区二区三区| 国精品午夜福利视频导航| 国产163黄网人看人人爽| 亚洲av伦理一区二区三区久久| 成人免费a级毛片天天看| 日韩欧美一区二区三区在线视频| 日韩激情视频在线看免费| 大鸡巴射在穴穴里的视频| 亚洲午夜国产片在线观看| 国产成人精品区在线观看| 白虎嫩穴抠逼高潮| 午夜国产精品午夜福利网| 国产一区二区三区在线观| 国产精品亚洲一区二区三区下载| 男女插插调教骚逼| 天堂久久久久久久久久久| 色欲精品一区二区三区AV| 色橹橹欧美在线观看视频高清免费| 波多野结衣高潮尿喷| 美女日比视频播放| 日本精品高清在线观看| 国产激情内射免费精品| 综合伊人久久在一二三区| 亚洲精品影片一区二区三区| 黑人大屌爆操骚货| 中文字幕一高清免费视频| 24日本精品视频免费| 大鸡吧小骚逼视频| 午夜精品福利一区二区三区蜜桃p| 欧美国产人妖另类色视频| 在线看免费无码a片视频| 捆绑调教白浆一区二区三区| 日韩欧美综合一二三区| 人妻含泪让粗大挺进| 青娱乐极品视觉导航| 欧美一区二区三区身体| 亚洲国产一区二区不卡在线资源| 国产高清一区二区三区四区色| 欧美大鸡巴操大骚逼| 中文字幕精品字幕一区二区三区|