亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to Finland

Release time:2023-11-12 15:26:31 Hits: Current position: Home > News

This article mainly introduces:

Finland hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

Finland tilting furnace hydraulic cylinder

(Finland tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tilting furnace hydraulic cylinder are widely used in Finland,because of no need for deceleration device,long service life,smooth movement.So our company has designed tilting furnace hydraulic cylinder for customers from Finland.

Introduction to tilting furnace hydraulic cylinder:

In use, the tilting furnace hydraulic cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the tilting furnace hydraulic cylinder.

The wear of the hard chromium plating layer of the tilting furnace hydraulic cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

At the rated pressure, the thrust of the tilting furnace hydraulic cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the tilting furnace hydraulic cylinder is related to the diameter of the tilting furnace hydraulic cylinder, but not to the stroke of the tilting furnace hydraulic cylinder. Moreover, the larger the tilting furnace hydraulic cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the tilting furnace hydraulic cylinder.

Most of the failure of the tilting furnace hydraulic cylinder is because there is a foreign body in the tilting furnace hydraulic cylinder into the failure of the tilting furnace hydraulic cylinder, the most problematic is that it is difficult to determine when the foreign body is into the tilting furnace hydraulic cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about tilting furnace hydraulic cylinder:

When the cylinder is tested, why can't the pressure be maintained with the balance valve?
Because the oil into the oil chamber through the hydraulic lock on the control oil circuit through the other side of the spool, the original valve is designed in this way. It locks the circuit after the oil supply circuit loses pressure, on the contrary, if you keep supplying pressure, it is always in the state of opening the other side of the one-way spool. So this valve can't be used in the test.

What factors does the movement speed of the cylinder in the hydraulic system depend on?
The hydraulic system should be the piston movement in the cylinder, and the speed should also be the speed of the piston, according to the piston speed formula: v=4qm/pai*(D^2-d^2) where q is the flow rate of the input hydraulic cylinder, m is the volumetric efficiency of the hydraulic cylinder, D, d is the diameter of the piston and piston rod, because other factors are determined, the movement speed of the cylinder depends on the flow rate.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本最新免费不卡一区二区三区| 大鸡巴插美女小逼逼| 亚洲欧美中文字幕第二十| 骚狐狸免费在线观看视频| 精品国产自在久国产应用| 午夜场射精嗯嗯啊啊视频| 成人黄色精品久久app| 欧美国产综合日韩一区二区| 国产一区二区三区三级88| 久久精品国产自清天天线| 在线观看国产黄色| 美国女人抠插bbb| 嗯嗯嗯啊啊啊好湿好痒好多水视频| 久久99热精品在线观看| 久操视频中文字幕在线观看| 顶的速度越来越快越| 为什么搜索不到裸体| 日韩免费一级a毛片在线播放一级| 国产精品久久大屁股白浆| 日韩人妻无码中字一区二区| 大鸡吧老外操中国逼| 国产亚洲一区白丝在线观看| 视频在线观看一区@99| 久久久国产系列丝袜熟女| 极品一区二区三区av| 欧美一区二区三区男人的天堂| 日本二区在线观看| 欧美黄色三级成人小视频| 男人的天堂日本在线观看| 2021最新热播国产一区二区| 国产精品538一区二区在线| 色一情一交一乱一区二区| 青娱乐极品视觉导航| 日本成人精品一区二区三区| 日本六十五十熟女一级黄色| 美女穿黑丝被大鸡巴猛操| 玖玖资源站无码专区| 3色w九九久久男人皇宫宕| 91午夜福利1000集| 春宵福利导航91| 777米奇在线视频无码|