亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Morocco

Release time:2023-11-12 14:24:39 Hits: Current position: Home > News

This article mainly introduces:

Morocco hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Morocco swager cylinder

(Morocco swager cylinder,produced by Hengyu Hydraulic Co., Ltd)

swager cylinder are widely used in Morocco,because of long service life,smooth movement,high work efficiency.So our company has designed swager cylinder for customers from Morocco.

Introduction to swager cylinder:

When using the swager cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the swager cylinder block. If the swager cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the swager cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the swager cylinder, so that the working efficiency of the swager cylinder is reduced.

The swager cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure swager cylinder can use 20 steel pipe, and the high pressure swager cylinder can use 45 steel pipe.

swager cylinders in series, parallel and series parallel. Series: In the swager cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the swager cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the swager cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the swager cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

swager cylinder use should try to avoid sealing belt into the swager cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the swager cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the swager cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

Answers to some questions about swager cylinder:

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

How to select swing cylinder? Under what conditions are they designed and selected?
1, determine the system parameters: ① the weight and the required force; ② Nominal working pressure and range; ③ The time required to travel this distance; 4 oil medium 2, installation method: select the appropriate way for the specific application 3, cylinder diameter and working pressure: determine the cylinder diameter and provide the necessary force required by the system pressure 4, piston rod: determine the minimum piston rod diameter required to withstand the longitudinal bending force, select the appropriate piston rod end and piston rod end thread 5, piston: Whether the seal type is suitable for the application 6, buffer: choose the buffer requirements as appropriate.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩码一码二码三码区别| 操久久久久久久久久久久久久久久久| 亚洲天堂网2020| 无码人妻视频一区二区三区| 哪里有免费黄色av| 国产成人欧美日本在线观看| 亚洲高清日韩中文字幕| 国产精品久久小视频| 亚洲gv永久无码天堂网| 波多野结衣av一区二区| 日韩精品一区二区三区视频最新| 国产麻豆精品三级在线播放| 日本午夜福利在线视频| 国产又长有粗的视频| 97精品国产综合久久| 亚洲成av一区二区三区| 国产精品人妻4p一区| 国产一区二区三区网址| 国产精品亚洲А∨天堂网不卡| 国产精品我不卡尤物| 精品国产日本一区二区| 95精品视频在线观看| 欧美中文亚洲国产日韩| 国产综合精品久久久久成人蜜臀| 日韩欧美中文字幕一区二区| 国产亚洲欧美另类网爆在线| 日韩在线观看一卡二卡| 精品国产自产在线观看| 2021国产三级精品三级在专区| 亚洲欧美日韩国产精品专区| 久久精品亚洲成在人线av| 2017中文字幕在线| 激情文学五月婷444| 亚洲一区二区三区中文字幕一本| 精品视频一区二区三区美女视频| 波多野结衣人妻奴隶| 在线无码中文强乱爆乳系列| 中文字幕日本一区二区在线观看| 中文字幕亚洲一区巨区| 婷婷色婷婷开心五月四房播播| 亚洲高清日韩中文字幕|