亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Colombia

Release time:2023-11-12 11:05:58 Hits: Current position: Home > News

This article mainly introduces:

Colombia hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Colombia track steering cylinder

(Colombia track steering cylinder,produced by Hebei Hengyu company)

track steering cylinder are widely used in Colombia,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed track steering cylinder for customers from Colombia.

Introduction to track steering cylinder:

In the case of serious wear on the inner surface of the track steering cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the track steering cylinder manufacturing process for replacement. The track steering cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

The difference between the plunger track steering cylinder and the piston track steering cylinder is that the piston in the track steering cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type track steering cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

Most of the failure of the track steering cylinder is because there is a foreign body in the track steering cylinder into the failure of the track steering cylinder, the most problematic is that it is difficult to determine when the foreign body is into the track steering cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

When installing the track steering cylinder pipe, the pipe should be cleaned after installation, and should not pass through the track steering cylinder block, and the by-pass pipe must be installed in front of the oil port of the track steering cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the track steering cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the track steering cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about track steering cylinder:

How to distinguish loader boom and forearm hydraulic cylinder? Is it the upper arm or the lower arm?
The one in the middle that can flip the bucket is the small arm cylinder you say, and the one that lifts the brackets (big arms) on both sides is the big arm cylinder.

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
91精品国产综合久久久蜜| 大鸡巴干浪穴视频| 国产午夜福利视频第三区| 亚洲欧美一区二区爽爽爽| 男男大鸡巴操小屁眼视频| 精品国产自在现线看| 欧美成人3p视频| 国产免费好大好硬| 麻豆视频一级片在线观看| 91成人精品国语自产拍| 亚洲高清中文字幕一区二区三区| 精品少妇一区二区三区中文字幕| 骚穴 操我 视频| 亚洲天堂av一区二区在线观看| 抽插肥嫩小穴的视频| 久久综合日韩亚洲精品色| 午夜成人理论片在线观看| 大鸡巴猛插小穴视频| 嗯啊好大好想要视频| 中文字幕精品字幕一区二区三区| 国产品无码一区二区三区在线| 欧美99热这里都是精品| 欧美一区亚洲一区视频在线观看| 精品国产Av无码久久久一区二区| 黄色免费老人操逼| 色老头av亚洲三区三区| 彩虹网免费视频在线观看| 欧美精品国产一区二区在线观看| 大鸡吧小骚逼视频| 黑人大鸡巴双插美女| 综合欧美日韩一区二区三区| 好爽又高潮了毛片在线看| 日本韩国国产精品一区| 99热这里只有精品98| 久久国产亚洲高清| 老太太在丛林日老B| 国产美女裸体视频全免费| 中国美女操逼的视频| 久久精品小视频/| 国产亚洲欧美日韩在线观看一区| 欧美在线A片一区二区三区|