亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailplate hydraulic cylinder Sold to Algeria

Release time:2023-11-12 11:05:41 Hits: Current position: Home > News

This article mainly introduces:

Algeria hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

Algeria tailplate hydraulic cylinder

(Algeria tailplate hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tailplate hydraulic cylinder are widely used in Algeria,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed tailplate hydraulic cylinder for customers from Algeria.

Introduction to tailplate hydraulic cylinder:

The difference between the integral tailplate hydraulic cylinder and the split tailplate hydraulic cylinder: The integral tailplate hydraulic cylinder and the split tailplate hydraulic cylinder in the tailplate hydraulic cylinder are two different tailplate hydraulic cylinders, and they are very different. The whole tailplate hydraulic cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split tailplate hydraulic cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and tailplate hydraulic cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

In order to ensure the service life of the tailplate hydraulic cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

If it is found that the tailplate hydraulic cylinder lubrication is poor or the tailplate hydraulic cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the tailplate hydraulic cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the tailplate hydraulic cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the tailplate hydraulic cylinder center line. In this way, when the piston works in the tailplate hydraulic cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the tailplate hydraulic cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

Most of the failure of the tailplate hydraulic cylinder is because there is a foreign body in the tailplate hydraulic cylinder into the failure of the tailplate hydraulic cylinder, the most problematic is that it is difficult to determine when the foreign body is into the tailplate hydraulic cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about tailplate hydraulic cylinder:

What's the use of three oil pipes on the cylinder?
The cylinder usually has an upper and lower oil chamber, one is connected to the upper oil chamber, one is connected to the lower oil chamber, sometimes a hydraulic lock will be added, that is, a hydraulic control check valve to prevent accidents when the oil pipe breaks, so the third pipe should be the control oil pipe of the hydraulic control check valve.

To achieve the same stroke, which is better, hydraulic cylinder or lead screw?
If there is batch action, then the hydraulic pressure is better. Hydraulic: smooth operation, no lubrication, easy control, high control accuracy (can use proportional or servo system), the key is to manually control, but certainly to support the hydraulic system, for a single action must cost. Maintenance costs are also high. Lead screw: simple structure, easy to achieve, convenient maintenance, but must be lubricated, can not be manual, or manual control is inconvenient. See where it is used, if it is used in high-precision occasions, it must only be hydraulic, because the lead screw has a gap. There are many hydraulic actions, the hydraulic system itself must be prepared, then the use of hydraulic pressure is also very economical.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品麻豆亚洲欧美| 两个人免费视频高清| 日本高清一区二区三区在线观看| 中国三级片在线视频| 伊人久久亚洲婷婷综合久久| 日韩视频无码日韩视频又2020| 高颜值美女视频在线观看| 久久久精品亚洲Av| 欧美日韩欧美国产中文字幕| 一区二区三区中文欧美| 好想大鸡巴插进阴道视频| 好嗨哟直播看片在线观看| 爱男爽高潮鸡穴视频| 91久久愉拍愉拍国产一区| av中文字幕一区二区精品久久| 国产精品一区二区三区涩涩av| 久久久久久久 亚洲精品| 国产中文字幕在线一区二区三区| 操我骚逼抽插视频| 自拍偷拍视频颜射| 99热这里只有精品97| 成人国产亚洲精品一区二| 国产一区二区三区精品片| 欧美一级免费观看| 男插女逼啪啪啪软件| 开心五月播五月亚洲第一| 从后面狠狠的干白嫩少妇| 插女生那个的视频| 99视频在线看免费视频| 人人超级碰青青精品| 美女扒开腿让男人桶爽揉| 极品一区二区三区av| 9国产亚洲精品国产| 亚洲高清无遮挡在线观看| 国产剧情使劲操我逼| 高清无码精品一区二区三区| 久久69精品久久久久免| 男生操女生无马赛克免费| 操女人逼逼骚逼逼| 69亚洲一级黄片| 伊人久久综合无码成人网|