亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

yg series hydraulic cylinder Sold to Britain

Release time:2023-11-06 22:53:43 Hits: Current position: Home > News

This article mainly introduces:

Britain yg series hydraulic cylinder,yg series hydraulic cylinder manufacturer

Britain yg series hydraulic cylinder

(Britain yg series hydraulic cylinder,produced by Hengyu Group)

yg series hydraulic cylinder are widely used in Britain,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed yg series hydraulic cylinder for customers from Britain.

Introduction to yg series hydraulic cylinder:

Before the yg series hydraulic cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

The quality of the yg series hydraulic cylinder can not be ignored in the purchase of the yg series hydraulic cylinder. The yg series hydraulic cylinder is the main component of the yg series hydraulic cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. yg series hydraulic cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of yg series hydraulic cylinder is deep hole processing, which has always troubled the processing personnel.

yg series hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the yg series hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

When installing the yg series hydraulic cylinder, the axial ends of the yg series hydraulic cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the yg series hydraulic cylinder, there is axial expansion. If the two ends of the yg series hydraulic cylinder are fixed, all parts of the yg series hydraulic cylinder will be deformed. When disassembling the yg series hydraulic cylinder, it is strictly forbidden to hammer the yg series hydraulic cylinder and the piston surface, such as the yg series hydraulic cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

Answers to some questions about yg series hydraulic cylinder:

Is the hydraulic cylinder leaking because there is no pressure?
HC hydraulic cylinder common leakage reasons, first: most of the reasons are because the seal surface wear or aging leads to poor sealing, so there is no pressure to operate, as long as the piston seal can be replaced. Second: It may also be the piston rod strain, repair the piston rod is good. If it is because the piston strength is not enough and the playing time is long, it is necessary to replace the piston.

What is hydraulic cylinder guide?
The cylinder itself can not move, the piston moves, the guide should be used to guide the mechanism connected with the piston extension end. For example, in the commonly used hydraulic press, the guide column above is used to guide the pressure plate connected with the piston.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产日韩一区在线观看视频| 蜜臀99久久精品久久久| 国产精品一区二区久久| 日韩一区二区三区视频| 亚洲午夜精品久久久久久浪潮| 99亚洲视频一区二区| 国产三级视频在线观看网站| 国产精品毛片大码女人| 精品视频一区二区三区美女视频| 一区二区三区四区欧美日韩亚洲| 中文人操人人插人免费看视频| 95精品视频在线观看| 国产精品久久小视频| 欧美乱码精品一区二区三区卡| 久久久久久三区二区精品| 操久久久久久久久久久久久久久久久| 国产三级黄色片观看| 国产精品日本一区二区在线看| 免费中文字幕一区二区| 欧美亚洲专区一区二区| 欧美日韩精品一区丁香| 日韩的一区二区另类免费| 亚洲线日本一区二区三区| 久久久久人妻精品明星换脸| 国产三级视频在线观看网站| 一本大道av伊人久久综合| 好看的福利电影在线| 日韩久久精品一区二区三区介绍| 99久久免费精品国产免费高清| 国产又长有粗的视频| 欧美日韩国产精品视频一区| 国产精品欧美大片在线观看| 在线十亚洲十欧美十日本专区| 亚洲一区二区三区中文字幕一本| 亚洲av成为人一区二区| 免费在线观看一本视频| 人之初av一区二区三区| 日韩在线中文字幕观看| 国产精品久久久久九九九九不卡| 亚洲国产精品午夜福利久久| 久久国产精品久久精品国产四虎|