亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

unidirectional cylinder Sold to Cote d 'Ivoire

Release time:2023-11-10 08:35:21 Hits: Current position: Home > News

This article mainly introduces:

Cote d 'Ivoire hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder

Cote d 'Ivoire unidirectional cylinder

(Cote d 'Ivoire unidirectional cylinder,produced by Hebei Hengyu company)

unidirectional cylinder are widely used in Cote d 'Ivoire,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed unidirectional cylinder for customers from Cote d 'Ivoire.

Introduction to unidirectional cylinder:

When the unidirectional cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the unidirectional cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

The repair method of the unidirectional cylinder: the repair of the unidirectional cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

How to repair the unidirectional cylinder body when it is damaged: When the unidirectional cylinder has trace deformation and shallow tensile marks, the unidirectional cylinder is repaired by strong honing process. The heavy honing process can repair unidirectional cylinders up to 2.5 times out of tolerance than the original tolerance. It honed the parts with excessive size or shape error through a powerful honing machine, so that the overall size, shape tolerance and roughness of the unidirectional cylinder can meet the technical requirements.

The wear of the hard chromium plating layer of the unidirectional cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

Answers to some questions about unidirectional cylinder:

Can a leak in the cylinder cause the hydraulic system to fail?
Leakage in the cylinder can cause the hydraulic system to fail. Cylinder leakage (internal leakage) first affects the controlled action of the hydraulic system can not meet the requirements (such as the movement speed of the cylinder, the insufficient thrust and tension of the cylinder), if the internal leakage of the cylinder is too large, it may also cause the cylinder to be unable to promote the load movement. Second, the existence of internal leakage (internal leakage) of the oil cylinder will lead to the rapid rise (or too high) of the oil temperature of the hydraulic system, and the high oil temperature will not only waste the energy conversion of the system, but also lead to the reduction of the viscosity of the oil, which will accelerate the aging and destruction of the seals such as pumps, valves, cylinders, pipelines, and at the same time, the lubrication effect of the hydraulic oil is reduced, and the production of iron filings that increase the friction of the hydraulic system.

Why does the hydraulic cylinder ring?
1 Air intrusion into the hydraulic system is the main reason for noise 2 The relief valve is unstable, such as due to the improper combination of the slide valve and the valve hole or the contact of the cone valve and the seat is stuck by dirt, the damping hole is blocked, the spring is crooked or fails to make the spool stuck or move in the valve hole, causing system pressure fluctuation and noise. 3 Improper adjustment of the reversing valve causes the spool of the reversing valve to move too fast, resulting in reversing impact, resulting in noise and vibration. 4 Mechanical vibration, such as long tubing, elbow more and not fixed, when the oil flow through, especially when the flow rate is high, easy to cause pipe shaking; The rotating part of the motor and hydraulic pump is unbalanced, or the alignment is not good during installation, or the coupling is loose, etc., which can produce vibration and noise.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品麻豆国产免费一区二区三区| 国产伦精品一区二区三区福利| 美女的咪咪和骚逼| 黄片大鸡吧操小逼| 欧美一区二区三区身体| 欧美一区二区高清视频在线观看| 女人操女人大逼大片| 综合伊人久久在一二三区| 正在播放舔穴视频| 正在播放舔穴视频| 日本高清不卡一区二区三区| 一区二区三区国产l精品欧美| 大鸡巴操屁眼无码| 国产熟女视频一区二区三区| 枫花恋精品一区二区久久| 久久久国产调教性奴| 亚洲 自拍 欧美 一区| 777米奇在线视频无码| 欧美亚洲另类天天综合网| 亚洲精品精品精国产| 91热国产在线观看| 把女生操出水的视频| 日本成人精品一区二区三区| 伊人网在线视频观看| 啦啦啦视频在线手机播放| 日本不卡免费一区二区视频| 好想大鸡巴插进阴道视频| 欧美国产综合日韩一区二区| 八插8插黄色视频| 久久一区二区三区精华液介绍| 国产精选三级在线观看| 中日韩VA无码中文字幕| 一区二区三区 日韩在线| 色噜噜噜噜一区二区三区| 藏经阁91福利私人试看| 国奴精品毛片av一区二区三区| 中国老女人 操逼 视频| 亚洲国产嫩草18久久久| 三级片手机在线视频| 色噜噜噜噜一区二区三区| 操纯欲女生小穴视频|