亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Ireland

Release time:2023-11-10 08:35:18 Hits: Current position: Home > News

This article mainly introduces:

Ireland hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Ireland track steering cylinder

(Ireland track steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

track steering cylinder are widely used in Ireland,because of long service life,smooth movement,no need for deceleration device.So our company has designed track steering cylinder for customers from Ireland.

Introduction to track steering cylinder:

If the track steering cylinder slips or crawls, please check whether there is astringency inside the track steering cylinder, because the internal parts of the track steering cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the track steering cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the track steering cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the track steering cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

Before the track steering cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

track steering cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the track steering cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Answers to some questions about track steering cylinder:

What is the bearing capacity of the HOB cylinder?
The normal specification of HOB is 140 kg pressure, which is more commonly used in the market, and there are clear marks on the cylinder, 210 kg is a strengthened version of HOB, generally customized cylinders are also clearly marked on the above, when the specific use of the cylinder, the maximum use pressure is marked on the cylinder.

Is there a way to make the cylinder stop pushing when it hits something hard during the process of pushing?
The simplest solution is to press the stop switch, this switch has a mechanical type, touch the object on the action or send a stop signal, through the operation of the motor control cylinder; There is also an induction switch, that is, when the hydraulic cylinder expands to the range of the induction switch can sense the signal, it sends a signal to let the motor act, resulting in the corresponding action of the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品熟女视频播放| 男生用鸡巴操女生的视频| 欧美男女舔逼舔鸡巴视频| 猛插女人小穴视频| 男人大鸡巴操女人的大逼| 啊啊好想被大鸡巴操视频| 黑人大鸡把操逼视频| 从后面进入嗯啊视频| 日韩在线视频不卡一区二区三区| 国产高清第一区第二区第一页| 伊人久久久久久久久香港| 色逼色逼色逼色逼色逼色| 久久国产精品成人18p| 亚洲高清中文字幕一区二区三区| 夜夜38亚洲综合网| 丝袜片一区二区三区四区五区| 女教师色色天天免费播放| 美女人的逼免费观看| 亚洲一级片在线播放| 精品久久久久久久人妻换| 三级片手机在线视频| 日韩av一区二区高清不卡| 激烈18禁高潮视频免费| 交换夫妇4中文字幕| 大鸡吧老外操中国逼| 黑人大鸡巴日小逼| 大鸡巴插美女小逼逼| 欧美 亚洲 日本 国产| 99精品欧美一区二区三区喷胶| 91精品国产剧情欧美一区二区| 亚洲欧美国产原创一区二区三区| 婷婷6月天丁香综合在线| 性一交一乱一乱一区二区| 女人扒开腿让我舔十八禁| 91秦先生全集在线观看| 美女骚逼黄色18禁| 日本精品久久人妻一区二区三区| 欧美一级淫片免费播放口| 中文欧美亚洲欧日韩| 国产乱理伦片在线观看夜| 二次元男生操女生屁眼爽|