亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Hungary

Release time:2023-11-10 08:34:46 Hits: Current position: Home > News

This article mainly introduces:

Hungary hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Hungary trunnion cylinder

(Hungary trunnion cylinder,produced by Hebei Hengyu company)

trunnion cylinder are widely used in Hungary,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed trunnion cylinder for customers from Hungary.

Introduction to trunnion cylinder:

The assembly work of the trunnion cylinder has a great impact on the quality of the trunnion cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Protection of the trunnion cylinder surface: During the dismantling process, safety protection should be carried out on the trunnion cylinder to prevent objects from falling and welding slag from falling to the surface, causing damage to the trunnion cylinder surface. In the process of propulsion, the damaged pipe segments should be prevented from falling and smashing, and the slurry remaining on the surface of the trunnion cylinder should be cleaned up in time.

Before purchasing the trunnion cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

If it is found that the trunnion cylinder lubrication is poor or the trunnion cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the trunnion cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the trunnion cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the trunnion cylinder center line. In this way, when the piston works in the trunnion cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the trunnion cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

Answers to some questions about trunnion cylinder:

100 tons press, the cylinder diameter is 250, how much pressure?
100 tons hydraulic press, if it is a single acting hydraulic cylinder, the required oil pressure is the nominal force divided by the cross-sectional area of the cylinder piston. One hundred tons of its pressure is 1000 kN (1000000N), the diameter of the cylinder is 250 mm, its area is the circular rate multiplied by the square of the radius, is 49062.5 square mm, and then the pressure divided by the area of the oil pressure is 20.38MPa. Therefore, a hydraulic pressure of 20.38 mpa is required for a 250 diameter cylinder to obtain 100 tons of pressure.

What is the material of the cylinder support ring?
Generally, it is polytetrafluoroethylene doped with copper powder, or polyformaldehyde, and copper sleeves, there are also nylon, resin and so on.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大鸡巴日小美女明星的BB| 大鸡吧小骚逼视频| 束缚久久久久久免费高潮| 鸡巴插骚逼视频欧美风格| 一色道久久88加勒比一| 国产乱理伦片在线观看夜| 99爱国产精品免费视频| av黄色资源在线观看| 国产女主播喷出白浆视频| 日韩高清毛片在线观看| 大黑鸡巴操模特骚B| 欧亚洲嫩模精品一区三区| 国产欧美一区二区精品久久久| 激情久久久久久久久久久| 男生插女生下面流出白色精液视频| 好爽轻点太大了太深了视频| 午夜性福福利视频一区二区三区| 美国大鸡巴操逼视频| 久久99国产中文| 性一交一子一伦一乱| 嗯嗯嗯啊啊啊好湿好痒好多水视频| 久久亚洲精品无码AV宋| 内射白嫩少妇超碰| 男生的小鸡鸡插进女生的桃子 里| 国产综合精品一区二区青青| 狠狠干无码日韩AV| 小美女淫荡的视频| 极品 操 抽插视频| 久久久国产调教性奴| 久久久久久久 亚洲精品| 麻豆国产欧美一区二区三区r| 操女人b直播软件| 黑人大鸡把操逼视频| 亚洲精品成人无码| 亚洲av熟妇高潮精品啪啪| 国产亚洲情侣久久精品| 亚洲一区二区三区四区国产| 国产青青操骚货在线观看| —级v免费大片欧美| 久久久国产调教性奴| 国产精品无码av在线一区|