亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to Panama

Release time:2023-11-08 15:23:47 Hits: Current position: Home > News

This article mainly introduces:

Panama hydraulic cylinder,tension cylinder manufacturer,tension cylinder

Panama tension cylinder

(Panama tension cylinder,produced by Hengyu Group)

tension cylinder are widely used in Panama,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed tension cylinder for customers from Panama.

Introduction to tension cylinder:

Under normal circumstances, the tension cylinder is composed of the rear end cover, body, piston, piston rod and front end cover and other main parts. In order to prevent the working medium from leaking out of the tension cylinder or from the high pressure chamber to the low pressure chamber, a sealing device (sealing ring) is arranged between the tension cylinder and the end cover, the piston and the piston rod, the piston and the tension cylinder, the piston rod and the front end cover. A dustproof device is also provided on the outside of the front end cover. In order to prevent the piston from impacting the end cap when it moves rapidly to the end of the stroke, the end of the tension cylinder can also be provided with a buffer device. If necessary, the exhaust device should be set in order to exhaust.

When the tension cylinder needs to be stored for a period of time, please follow the recommended methods: The tension cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the tension cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil tension cylinder should not be in direct contact with water vapor for a long time. The tension cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the tension cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the tension cylinder Before working, the tension cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the tension cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

When the tension cylinder is installed, the piston and the tension cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the tension cylinder head boss is easy to cause scars when it hits the inner surface of the tension cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized tension cylinders, only careful and careful operation can be avoided.

tension cylinder hydraulic oil selection: The recommended working oil viscosity of the tension cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

Answers to some questions about tension cylinder:

Injection molding machine die thimble on the side of the feed nozzle, the oil cylinder pull the thimble shift, how to debug the oil cylinder?
The cylinder is connected with the neutron of the injection molding machine, the neutron is retreated after the opening mold is in place, the cylinder taps the thimble plate to the top, and then takes, and the neutron is reset.

What is the meaning of dead volume in hydraulic cylinder?
Closed volume, also known as dead zone volume Positive displacement pump is dependent on the change of sealing working volume to achieve suction and pressure oil, in order not to make the suction and pressure oil cavity interworking, there is an oil sealing area between the suction and pressure oil cavity, when the sealing working volume passes through the oil sealing area, neither pressure oil cavity nor oil suction cavity communication, forming a closed sealing volume. The unloading groove is opened, and the grooving principle is that the sealing volume decreases and the oil pressure chamber is communicated, and the sealing volume increases and the oil suction chamber is communicated.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品福利一区二区三区在线观看| 高清无码精品一区二区三区| 新视觉亚洲三区二区一区理伦| 欧美十八一区二区三区| 国产精品久久大屁股白浆| 欧美高清一二三区| 一级做a爱过程免费视频俩| 亚洲欧美日韩精品一区二区| 鸡巴插骚逼真舒服| 爽妇网国产精品24| 骚货 淫水 国产| 国产欧美一二区不卡视频| 国产精品无码av在线一区| 久久久精品日韩一区二区三区| 欧美99热这里都是精品| 欧美后入尻逼视频| 被下药强奷到舒服的视频| 在线免费看污视频| 亚洲一区二区三成人精品| 久久久中文字幕在线视频| 欧美国产人妖另类色视频| 抽插肥嫩小穴的视频| 欧美一区二区高清视频在线观看| 精品国产自在现线看| 国产精品自在拍首页| 色逼色逼色逼色逼色逼色| 日韩一区二区三区夜色视频| 亚洲精品成人无码app| avtt天堂网先锋伦理| 一区二区三区中文欧美| 午夜成人理论片在线观看| 白嫩在线亚洲观看| 大鸡巴插入阴道视频| 尤物网三级在线观看| 欧美日韩综合在线一区| 呦交小u女国产精品99| 日韩精品高清在线| 中文有码无码人妻在线看| 中文无码av动作片| 免费看黑人操逼视频| 3色w九九久久男人皇宫宕|