亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailplate hydraulic cylinder Sold to Sudan

Release time:2023-11-08 15:23:34 Hits: Current position: Home > News

This article mainly introduces:

Sudan hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

Sudan tailplate hydraulic cylinder

(Sudan tailplate hydraulic cylinder,produced by Hengyu Group)

tailplate hydraulic cylinder are widely used in Sudan,because of long service life,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed tailplate hydraulic cylinder for customers from Sudan.

Introduction to tailplate hydraulic cylinder:

In recent years, the processing process of the tailplate hydraulic cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

If the tailplate hydraulic cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

Protection of the tailplate hydraulic cylinder surface: During the dismantling process, safety protection should be carried out on the tailplate hydraulic cylinder to prevent objects from falling and welding slag from falling to the surface, causing damage to the tailplate hydraulic cylinder surface. In the process of propulsion, the damaged pipe segments should be prevented from falling and smashing, and the slurry remaining on the surface of the tailplate hydraulic cylinder should be cleaned up in time.

tailplate hydraulic cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards tailplate hydraulic cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the tailplate hydraulic cylinder guide is determined by the length of the stroke. Check the strength of tailplate hydraulic cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

Answers to some questions about tailplate hydraulic cylinder:

Need a hydraulic cylinder, vertical upward 10 seconds to lift 20 tons of weight up 2 meters, how large cylinder and rod, how much pressure to use the plunger pump and how big?
The first thing to determine the system pressure, let's say 25 mpa, can take into account cost and performance. 1 Cylinder area 20000/250=80 square cm cylinder diameter (80/3.14) squared x2=200 mm 2 cylinder volume 80x200=16000 ml =16 L 3 Required pump flow 16x60/10=96 L/min 4 Power 96x25/55=43 kW 45 kW motor is available.

Can a leak in the cylinder cause the hydraulic system to fail?
Leakage in the cylinder can cause the hydraulic system to fail. Cylinder leakage (internal leakage) first affects the controlled action of the hydraulic system can not meet the requirements (such as the movement speed of the cylinder, the insufficient thrust and tension of the cylinder), if the internal leakage of the cylinder is too large, it may also cause the cylinder to be unable to promote the load movement. Second, the existence of internal leakage (internal leakage) of the oil cylinder will lead to the rapid rise (or too high) of the oil temperature of the hydraulic system, and the high oil temperature will not only waste the energy conversion of the system, but also lead to the reduction of the viscosity of the oil, which will accelerate the aging and destruction of the seals such as pumps, valves, cylinders, pipelines, and at the same time, the lubrication effect of the hydraulic oil is reduced, and the production of iron filings that increase the friction of the hydraulic system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品无码av在线一区| 捆绑调教白浆一区二区三区| 鸡巴操美女小穴羞羞视频| 性一交一子一伦一乱| A级毛片毛片免费观看久| 男插女下面高潮视频| 亚洲Av无码专区一区二区三区| 亚洲Av无码专区一区二区三区| 欧美一区二区高清视频在线观看| 哈啊慢点不要了视频| 欧美另类在线观看| 欧美日韩在线成人| 无码人妻精品一区二区三区蜜桃| 伊人久久久久久久久香港| 欧美人人做人人爽人人喊| 欧美一区二区三区身体| 性一交一子一伦一乱| 久久久久久国产A免费观看| 爽妇网国产精品24| 九九在线精品亚洲国产| 波多野结衣福利视频| 美女亚洲福利视频| 国产老妇伦国产熟女91| 精品精品国产一区二区性色av| 国产成人AV一区二区在线观看| 青娱乐欧美性爱视频| 中文字幕亚洲精品女同一页| 大黑鸡巴操模特骚B| 丝袜片一区二区三区四区五区| 欧美性做爰片免费视频看| 曰木高清免费一本| 免费人成再在线观看| 男的日女生批网页| 快速了解国产一级a爱片| 一区二区三区中文欧美| 精品麻豆国产免费一区二区三区| 操大屌粉的小穴视频| 非洲人粗大长硬配种视频| 欧美一级淫片免费播放口| 久久久五月性色视频| 爱爰哦好粗好猛操b视频|