亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

series synchronous cylinder Sold to Korea

Release time:2024-01-05 16:43:18 Hits: Current position: Home > News

This article mainly introduces:

Korea hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

Korea series synchronous cylinder

(Korea series synchronous cylinder,produced by Hengyu Hydraulic Cylinder Factory)

series synchronous cylinder are widely used in Korea,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed series synchronous cylinder for customers from Korea.

Introduction to series synchronous cylinder:

The repair method of series synchronous cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

If the seal of the series synchronous cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

series synchronous cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the series synchronous cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Before the series synchronous cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

Answers to some questions about series synchronous cylinder:

What does cylinder hob125*100 mean?
HOB is a series of hydraulic cylinder products, the use of pressure 14MPA, tie rod structure. 125 refers to the diameter of the cylinder and 100 refers to the stroke. The unit is millimeters.

How is the cylinder of hydraulic cylinder processed?
As the main parts of hydraulic cylinder, mining single pillar, hydraulic support, gun barrel and other products, its processing quality directly affects the life and reliability of the whole product. Cylinder processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of cylinder is deep hole processing, which has always troubled the processing personnel. Due to the residual compressive stress on the surface of the surface layer, the rolling machining is helpful to seal the small cracks on the surface and prevent the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the cylinder can be improved.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女逼男逼小穴小骚下载| 91午夜福利1000集| 非洲人粗大长硬配种视频| 大逼女人污污视频| 久久久国产精品亚洲无码| 欧美日韩视频在线一区二区| 日韩精品无码一区二区三区不卡| 久久婷婷综合五月一区二区| 国产精品免费第一区二区| 欧美成人精品一区二区免费看| 韩国三级a视频哪里看| 国产一区二区在线观看精品| 午夜色大片在线免费观看| 淫荡淫水逼操烂视频| 欧美亚洲熟妇视频在线观看| 欧美巨屌虐无毛骚逼| 又色又爽又黄的吃奶Av| 三级片在线无码播放| 好爽轻点太大了太深了视频| 啊啊啊好爽高潮啦| 被下药强奷到舒服的视频| 野外日逼视频免费看| 亚洲天堂av一区二区在线观看| 干女人逼逼的大几把| 精品国产Av无码久久久一区二区| 91在线一区二区| 久久精品伦一区二区三区| 女人张开腿让男人捅个爽| 尤物性生活午夜在线视频| 欧美人与兽大屌肛交爆菊| 老湿机69福免费破解版| 国产中文字幕在线一区二区三区| 欧美巨屌虐无毛骚逼| 极品 操 抽插视频| 中文字幕乱码人妻一区二区三区| 加勒比在线不卡一区二区观看| 日韩视频无码日韩视频又2020| 国产精品久久一区二区三区动| 国产欧美日本韩国一区二区| 国产品无码一区二区三区在线| 国产精品亚洲一区二区三区下载|