亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

plunger type cylinder Sold to Slovenia

Release time:2023-12-21 12:32:54 Hits: Current position: Home > News

This article mainly introduces:

Slovenia hydraulic cylinder,plunger type cylinder manufacturer,plunger type cylinder

Slovenia plunger type cylinder

(Slovenia plunger type cylinder,produced by Hengyu Hydraulic Co., Ltd)

plunger type cylinder are widely used in Slovenia,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed plunger type cylinder for customers from Slovenia.

Introduction to plunger type cylinder:

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

How to determine the working pressure of the plunger type cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, plunger type cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

In the case of serious wear on the inner surface of the plunger type cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the plunger type cylinder manufacturing process for replacement. The plunger type cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

When the plunger type cylinder needs to be stored for a period of time, please follow the recommended methods: The plunger type cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the plunger type cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil plunger type cylinder should not be in direct contact with water vapor for a long time. The plunger type cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the plunger type cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the plunger type cylinder Before working, the plunger type cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the plunger type cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

Answers to some questions about plunger type cylinder:

What is the pressure provided for a 63-bore cylinder with a pressure of 2 mpa?
2 mpa pressure is equivalent to 20 kg per square centimeter, 6.3 cm straight longitude, 3.15 cm radius, square, multiplied by, calculated an area of about 31.5 square centimeters, multiplied by 20 kg, the pressure is about 630 kg.

Is the hydraulic cylinder leaking because there is no pressure?
HC hydraulic cylinder common leakage reasons, first: most of the reasons are because the seal surface wear or aging leads to poor sealing, so there is no pressure to operate, as long as the piston seal can be replaced. Second: It may also be the piston rod strain, repair the piston rod is good. If it is because the piston strength is not enough and the playing time is long, it is necessary to replace the piston.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲欧洲综合成人综合网| 国产伦精品一区二区三区福利| 精品无码国产一区二区三区A| 大胸瑟瑟黑丝午夜| 被春药女高潮抽搐喷水视频| 欧美日韩久久一区二区三区| 亚洲福利左线观看| 帅哥大鸡巴操美女| 精品精品国产一区二区性色av| 老色鬼精品视频二区三区| 美女荒郊野外找男人靠逼| 国产精品粉嫩懂色av| 国产亚洲精品一区久久| 欧美国产三级片久久高清| 精品国产自在现线看| 爽妇网国产精品24| 日韩欧美一级特黄大片欧| avtt天堂网先锋伦理| 99精品一级欧美片免费| 九九热在线精品免费看| 国产精品欧美久久久久久| 八插8插黄色视频| 国产精品视频一区二区三区分享| 亚洲精品影片一区二区三区| 午夜场射精嗯嗯啊啊视频| 欧美日韩一区二区成人在线| 久久综合日韩亚洲精品色| 大鸡巴操逼 公司| 无码毛片一区二区本码视频| 可以免费看黄的香蕉视频| 国产熟女视频一区二区三区| 国产伦精品一区二区三区福利| 69国产成人综合久久精| 翘臀小穴在线观看| 大鸡吧视频在线观看| 亚洲乱码专区一区二区三区四区| 爱爰哦好粗好猛操b视频| 亚洲AV无码一区二区三区系列| 中文字幕在线精品的视频| 内射后入在线观看一区| 大香蕉尹人97超级视频|