亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push plate cylinder Sold to Malaysia

Release time:2023-12-21 12:32:52 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,push plate cylinder manufacturer,push plate cylinder

Malaysia push plate cylinder

(Malaysia push plate cylinder,produced by Hebei Hengyu company)

push plate cylinder are widely used in Malaysia,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed push plate cylinder for customers from Malaysia.

Introduction to push plate cylinder:

The piston rod and guide sleeve function of the push plate cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

The commonly used buffer structure of the push plate cylinder is composed of a piston boss and a push plate cylinder head groove. When the piston moves close to the push plate cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

When installing the push plate cylinder, the axial ends of the push plate cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the push plate cylinder, there is axial expansion. If the two ends of the push plate cylinder are fixed, all parts of the push plate cylinder will be deformed. When disassembling the push plate cylinder, it is strictly forbidden to hammer the push plate cylinder and the piston surface, such as the push plate cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

When the hydraulic oil is not pumped into the push plate cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the push plate cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

Answers to some questions about push plate cylinder:

Hydraulic cylinder performance requirements?
Hydraulic cylinder performance requirements: hydraulic cylinder is the hydraulic system to achieve energy transfer, conversion and control of the working medium, in addition, it is also responsible for the lubrication of the system, rust prevention, corrosion prevention and cooling. The performance of hydraulic oil will make the system flexible, accurate and reliable. Hydraulic performance requirements are determined according to the design parameters of the hydraulic system, operating conditions, the structure of the hydraulic pump and the working environment. Appropriate viscosity and good viscosion-temperature performance Viscosity is an important performance indicator of hydraulic pressure, which has an important impact on the smooth operation of the hydraulic system and the friction parts. The low temperature performance of hydraulic oil includes three aspects: low temperature flow, low temperature start-up and low temperature pumping.

When the hydraulic cylinder changes from fast to slow, how can the slow speed become more even and the speed can be adjusted?
Reversing valve set 2 reversing valves. The back of one valve goes directly to the cylinder, running at full speed for fast action. Add a speed control valve behind the other valve, and then connect to the cylinder to achieve slow action, you can adjust the opening of the speed control valve, to achieve the speed of the cylinder can be adjusted. An import speed control valve to more than 1,000 yuan, if you think it is too expensive, you can also use the throttle valve instead. However, the throttle valve is greatly affected by the load change.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
久久久久国产精品老熟女| 国产日欧一片内射午夜| 国内精品久久久久久久久久久| 国产精品日韩主播无套| 中文字幕人妻女同一区| 国产精品一区二区30p| 亚洲成人久久久久久久| 日本成人一区二区不卡| 国产精品va在线观看老妇女| 91精品一区二区三区蜜臀| 日本伊人久久精品视频| 久久久久成人精品免费播放寂寞少妇| 超碰人人在线免费观看| 日韩精品一区二区三区四区| 日韩码一码二码三码区别| 久久蜜臀亚洲一区二区| 久久久久无码精品国产app| 丰满少妇人妻久久久久久| 国产精品人成在线观看不卡| 欧美日本一道本一区二区三区| 婷婷激情网五月天亚洲| 国产资源网中文最新版| 国产日韩欧美中文字幕在线| 国产精品综合久久久久久| 欧美一级黄片在线播放| 亚洲欧洲欧美中文日韩| 国产一二三区亚洲欧美| 久久中文字幕一区不卡| 久久精品成人免费国产| 美女久久久高潮喷水91| 99久久免费精品国产免费高清| 亚洲国产精品无码av| 国产一级二级三级在线观看| 中文字幕熟女一区二区三区| 国产高清国内精品福利免费| 精品人妻一区二区三区久久夜夜嗨| 苍井空一区二区三区在线观看| 久久99热精品首页| 精品无码中文字幕在线| 欧美高清性做爰销魂在线| 国产欧美精品区一区二区三区竹菊|