亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stainless steel cylinder Sold to Sri Lanka

Release time:2023-11-08 10:37:13 Hits: Current position: Home > News

This article mainly introduces:

Sri Lanka hydraulic cylinder,stainless steel cylinder manufacturer,stainless steel cylinder

Sri Lanka stainless steel cylinder

(Sri Lanka stainless steel cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stainless steel cylinder are widely used in Sri Lanka,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed stainless steel cylinder for customers from Sri Lanka.

Introduction to stainless steel cylinder:

The stainless steel cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the stainless steel cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The stainless steel cylinder is basically composed of stainless steel cylinder and stainless steel cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

stainless steel cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the stainless steel cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

The stainless steel cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure stainless steel cylinder can use 20 steel pipe, and the high pressure stainless steel cylinder can use 45 steel pipe.

When the oil pressure of the stainless steel cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

Answers to some questions about stainless steel cylinder:

What is the material of the lift cylinder?
The cylinder is composed of many parts. The cylinder also contains the seal and the installation port at both ends, the material of these two parts is not easy to determine if there is no physical object. The cylinder body is generally 20 steel, 45 steel, 27SiMn and other materials, and the piston rod is generally 40Cr, 45 steel and other materials.

How to calculate cylinder speed?
If there is a throttle valve, the cylinder speed will be adjustable. When the throttle is fully opened, the speed of the cylinder reaches the maximum: maximum speed = oil pump displacement ÷ cylinder cavity cross-sectional area The displacement of the oil pump is a main indicator, which can be found on the nameplate, and some can also be known by the oil pump model; The cross-sectional area of the cylinder cavity can be easily calculated. Just make sure the units are the same. And because the cross-sectional area of the rod cavity and the rodless cavity of the cylinder is different, the speed of advance and retreat may also be different.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
人妻含泪让粗大挺进| 精品美女久久久久久嘘嘘| 啊服慢一点插入逼逼| 国产一区二区三区免费观在线| 骚货 淫水 国产| av人摸人人人澡人人超| 国产精品国产精黄 | 美女人的逼免费观看| 亚洲精品伦理熟女国产| 啊灬啊别停灬用力啊男男在线观看| 国产精品久久一区二区三区夜色| 色橹橹欧美在线观看视频高清免费| 久久久中文字幕一区| 看小伙草白女人比的黄片| 精品久久久久五月婷五月| 99爱这里只有精品| 国产亚洲欧美日韩在线观看一区| 蜜桃av噜噜一区二区三区免费| 日韩美女黄大片在线观看| 泡芙啪啪啪黄色污污| 午夜国产三级一区二区三| 夜夜嗨av少妇一二三区| 黄网官方在线观看| 国产午夜高清无码一级片| 国产高清在线观看一区二区三区| 国产精品自在自线。| 日韩 中文字幕在线最新| 午夜成人理论片在线观看| 大鸡巴操饿罗斯女人| 日韩乱码一区二区三区中文字幕| 中文字幕av一区二区三区蜜桃| 亚洲综合一区国产精品| 欧美日韩国产这里只有精品| 99热这里只有精品98| 韩国无玛黄片毛片| 啊啊啊别操了视频| 我最爱操女人的骚逼| 日本成人在线一区中文字幕| 日韩精品高清在线| 日本一区二区高清免费不卡| 两人爽爽爽无码免费视频|