亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Oman

Release time:2023-12-12 10:13:47 Hits: Current position: Home > News

This article mainly introduces:

Oman hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Oman stacker cylinder

(Oman stacker cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stacker cylinder are widely used in Oman,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed stacker cylinder for customers from Oman.

Introduction to stacker cylinder:

How to determine the working pressure of the stacker cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, stacker cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

stacker cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the stacker cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

The scar on the sliding surface of the stacker cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the stacker cylinder wall. Therefore, before installation, these scars must be fully repaired.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the stacker cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

Answers to some questions about stacker cylinder:

How to select swing cylinder? Under what conditions are they designed and selected?
1, determine the system parameters: ① the weight and the required force; ② Nominal working pressure and range; ③ The time required to travel this distance; 4 oil medium 2, installation method: select the appropriate way for the specific application 3, cylinder diameter and working pressure: determine the cylinder diameter and provide the necessary force required by the system pressure 4, piston rod: determine the minimum piston rod diameter required to withstand the longitudinal bending force, select the appropriate piston rod end and piston rod end thread 5, piston: Whether the seal type is suitable for the application 6, buffer: choose the buffer requirements as appropriate.

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲国产国产综合一区首页| 亚洲综合色88综合天堂| 最新的精品亚洲一区二区| 精品一区二区久久久久无码| 欧洲老妇人操大逼| 国产熟女视频一区二区三区| 国产亚洲欧美日韩在线观看一区| 亚洲精品成人无码app| 女女同性女同1区二区三| 把美女日到高潮喷水视频| 西西大尺度无码免费视频| 99精品一级欧美片免费| 亚洲国产精品伦理在线看| 欧美日韩一级视频| 99热这里只有精品97| 大胸美女被c的嗷嗷叫视频| 咪咪爱一级特黄大片| 白虎嫩穴抠逼高潮| 非洲大鸡巴操逼黄色录像| 欧美性一区二区三区五区| 久久久精品日韩一区二区三区| 男生狂操女生污视频| 亚洲国际精品一区二区| 日韩素人精品亚洲热一区| 92婷婷伊人久久精品一区二区| 白色紧身裤无码系列在线| 鸡巴插骚逼视频欧美风格| 大几吧插进小穴视频| 日本入室强伦姧人妻中文| 亚洲日韩国产欧美久久久| 亚洲精品美女久久久| 国产高清免费一级a久久| 黑人大屌大战中国女| 又色又爽又黄的吃奶Av| 国产一国产一级毛片无码视频百度| 日韩 欧美 成人 免费| 99久久精品国产一区二区成人了| 欧美老熟妇又粗又大| 精彩欧美一区二区三区| 中日韩VA无码中文字幕| 国产成人无码91精品一区|