亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

forklift hydraulic cylinder Sold to Switzerland

Release time:2023-12-11 09:05:14 Hits: Current position: Home > News

This article mainly introduces:

Switzerland hydraulic cylinder,forklift hydraulic cylinder manufacturer,forklift hydraulic cylinder

Switzerland forklift hydraulic cylinder

(Switzerland forklift hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

forklift hydraulic cylinder are widely used in Switzerland,because of no need for deceleration device,no transmission clearance,excellent temperature resistance.So our company has designed forklift hydraulic cylinder for customers from Switzerland.

Introduction to forklift hydraulic cylinder:

The advantages and disadvantages of the forklift hydraulic cylinder: the surface of the forklift hydraulic cylinder by painting, coating protection treatment, bright luster is not easy to rust, all raw materials of the forklift hydraulic cylinder through the top heat treatment, high manufacturing precision, belongs to the precision machinery, has a simple structure, stable quality, high mechanical efficiency, easy to achieve automation and many other advantages. However, hydraulic technology also has the shortcomings of oil leakage, oil temperature change affecting the control of running speed, noise, expensive cost and high maintenance cost.

If the piston rod and forklift hydraulic cylinder are stuck or the forklift hydraulic cylinder is blocked, at this time, no matter how to operate, the forklift hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the forklift hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the forklift hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

Do not enter foreign bodies when installing the forklift hydraulic cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

Answers to some questions about forklift hydraulic cylinder:

Why does the hydraulic cylinder rebound after the rod cavity is extended into place?
The reason is that after the rod cavity is extended into place, the rod cavity and the rodless cavity are connected, so that the cylinder moves towards the rod cavity. After connecting, it is equivalent to the hydraulic oil directly driving the cylinder with an area equal to the piston rod. After the end of this problem, it is estimated that the seal is not very good, and the two cavities are connected after the pressure is increased to a certain extent; Or there is a problem in the valve, so that the two chambers are connected after reaching a certain pressure. Other phenomena: If the load is increased to a certain extent, no matter which side of the solenoid valve is energized, the cylinder will move to the rod cavity.

How is the cylinder of hydraulic cylinder processed?
As the main parts of hydraulic cylinder, mining single pillar, hydraulic support, gun barrel and other products, its processing quality directly affects the life and reliability of the whole product. Cylinder processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of cylinder is deep hole processing, which has always troubled the processing personnel. Due to the residual compressive stress on the surface of the surface layer, the rolling machining is helpful to seal the small cracks on the surface and prevent the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the cylinder can be improved.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩国产精品视频一区| 国产精品无码毛片久久久| 999久久久国产大美腿| 爆乳喷奶水无码正在播放| 爱爱视频小抽插动漫| 使劲操我小穴视频| 日本精品久久不卡一区二区| 欧美日本欧美日本区一区二| 国产裸体视频BBBBB| 一区二区国产精品免费视频| 国产又粗又猛又色又免费| 爱爱视频小抽插动漫| 久久国产精品成人18p| 最新黄色A级一短片| 欧洲老妇人操大逼| 美女日逼视频免费| 成年人的一级黄色带| 亚洲一区二区三成人精品| 日本精品久久不卡一区二区| 啊灬啊别停灬用力啊男男在线观看| 色一情一交一乱一区二区| 国产裸模大尺度私拍视频| 国产精品无码av在线一区| 操大屌粉的小穴视频| 亚洲 自拍 欧美 一区| 淫荡扣逼骚逼视频| 国产在线中文字幕一区二区三区| 日韩美女在线视频一区不卡| 日本成人在线一区中文字幕| 操国产骚逼逼逼逼逼逼逼| 亚洲综合无码一区二区丶| 久久精品欧美日韩精品不卡| 久久精品男人的天堂av| 国产女明星一级毛片| 久久久久精品无码专区喝奶| 看小伙草白女人比的黄片| 中文有码无码人妻在线看| 看看美日韩操逼吧| 插我舔内射18免费视频| 黑人大屌大战中国女| 国产成人精品区在线观看|