亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reset cylinder Sold to S.Africa

Release time:2023-12-09 16:24:28 Hits: Current position: Home > News

This article mainly introduces:

S.Africa hydraulic cylinder,reset cylinder manufacturer,reset cylinder

S.Africa reset cylinder

(S.Africa reset cylinder,produced by Hengyu Hydraulic Cylinder Factory)

reset cylinder are widely used in S.Africa,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed reset cylinder for customers from S.Africa.

Introduction to reset cylinder:

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular reset cylinder action. Troubleshooting method: Replace the rubber hose.

After chrome plating of the piston rod of the reset cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

The definition of the minimum stable speed refers to the minimum movement speed of the reset cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the reset cylinder that undertakes different work has different requirements for the minimum stable speed.

The material of the sliding part of the reset cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

Answers to some questions about reset cylinder:

What is the clearance between the cylinder and the piston?
The gap between the cylinder and the piston in the radius is generally 40 wires, that is, about 0.4mm, and the gap of the cylinder with different diameters will be slightly different. Generally, the inner diameter of the cylinder is larger than the outer diameter of the piston, so as to prevent the friction between the outer surface and the inner surface of the cylinder during the operation of the piston. In order to ensure that the cylinder has a rod cavity and a rodless cavity seal, a sealing device, that is, a sealing ring, is installed on the outer surface of the piston. The sealing ring form is not exactly the same, the O-type sealing ring is generally used under low pressure, and the lip sealing ring is used under high pressure. At the same time, the outer circle of the piston is also equipped with a dust ring and a wear ring. As long as the cylinder seal fails, all the internal seals should be replaced.

Can the hydraulic oil in the cylinder return to the tank?
Yes, there is a way, for example, first remove the cylinder from the machine, and then connect the two pipes on the cylinder, so that the cylinder piston rod is completely retracted into the cylinder, at this time, the piston is with the bottom, and the rear chamber is almost no oil, and then screw off the joint at the end of the front chamber by the hydraulic station, and put it in an empty bucket. Finally, insert the gas pipe into the oil port of the rear chamber. Open the air source, and then the rod will run out, and you'll drain the hydraulic oil from the end of the rod, which requires a source of air on site.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧洲老妇人操大逼| 欧美高清在线观看一区二区三区| 中文字幕亚洲欧美精品一区二区| 中文字幕人妻一区二区三区人妻| 国产高清在线观看一区二区三区| 久久久国产系列丝袜熟女| 很黄很爽的免费视频大全| 那种视频在线观看你懂的| 欧美一区二区三区身体| 高颜值情侣鸡巴插插淫叫| 日韩有码一区二区三区在线观看| 国产乱理伦片在线观看夜| 女人的骚逼免费视频| 国产亚洲欧美日韩在线观看一区| 美女被插入小穴爆操视频| 欧美日韩久久一区二区三区| 久久久18禁一区二区网| 黑人巨茎和中国美女视频| 黑人大屌大战中国女| 人妻波多野结衣爽到喷水| 野外日逼视频免费看| 天天爽夜夜爽夜夜爽一区| 欧美日韩国产欧美| 黑丝美女被操哭边操边尿| 少妇无码一区二区二三区| 久久久久久久 亚洲精品| 国产成人无码91精品一区| 瓯美在线免费视频笫一区第二区| 国产一区二区三区午夜精品久久| 亚洲国产日韩欧美高清片| 大鸡吧老外操中国逼| 色999日韩自偷自拍美女| 大黑屌日本另类肛交| 内射白嫩少妇超碰| 大鸡巴狂插嫩逼视频| 中文无码av动作片| 日韩精品一区二区天堂| 国产精品538一区二区在线| 欧美日本欧美日本区一区二| 黄色录像片操大逼的| av中文字幕一区二区精品久久|