亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

sanitation truck hydraulic cylinder Sold to Sweden

Release time:2023-12-09 16:24:26 Hits: Current position: Home > News

This article mainly introduces:

Sweden hydraulic cylinder,sanitation truck hydraulic cylinder manufacturer,sanitation truck hydraulic cylinder

Sweden sanitation truck hydraulic cylinder

(Sweden sanitation truck hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

sanitation truck hydraulic cylinder are widely used in Sweden,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed sanitation truck hydraulic cylinder for customers from Sweden.

Introduction to sanitation truck hydraulic cylinder:

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the sanitation truck hydraulic cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The material of the sliding part of the sanitation truck hydraulic cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

How to determine the working pressure of the sanitation truck hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, sanitation truck hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

sanitation truck hydraulic cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

Answers to some questions about sanitation truck hydraulic cylinder:

Is rubber or polyurethane better for V-ring of hydraulic cylinder?
The hydraulic cylinder V-type seal ring is better with polyurethane, and chlorine rubber is used for various chemicals and high temperatures, especially when there are wear-resistant requirements, polyurethane rubber is needed. But the price of polyurethane rubber is much more expensive than the price of rubber. However, the V-ring material is most commonly used in nitrile and neoprene rubber, and natural rubber is used for sealing water and air. Butyl rubber is used for non-combustible hydraulic fluids and phosphate ester hydraulic fluids. The advantage is that the price is cheaper than the polyurethane material, and the disadvantage is that it is not wear-resistant and the anti-aging property is relatively poor.

What factors does the movement speed of the cylinder in the hydraulic system depend on?
The hydraulic system should be the piston movement in the cylinder, and the speed should also be the speed of the piston, according to the piston speed formula: v=4qm/pai*(D^2-d^2) where q is the flow rate of the input hydraulic cylinder, m is the volumetric efficiency of the hydraulic cylinder, D, d is the diameter of the piston and piston rod, because other factors are determined, the movement speed of the cylinder depends on the flow rate.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
操女人b直播软件| 最新免费高清无码片| 亚洲欧美日韩中文v在线| 中文字幕一区二区 在线| 久久亚洲精品无码AV宋| 我要看成人免费毛片| 老司机精品免费在线视频| 美女骚逼被操出白浆| 欧美丰满大屁股女人的逼被操视频| 欧美在线A片一区二区三区| 欧美区 日韩区 亚洲区| 激情五月六月婷婷俺来也| 男人操女人下面国产剧情| 亚洲一区二区三区精品日韩| 操老骚逼三级黄视频| 老熟妇高潮一区二区高清视频| 少妇无码一区二区二三区| 日本高清一区二区三区不卡| 99爱国产精品免费视频| 精品日本一区二区三区视频播放| 久久国产老熟女老女人| 麻豆国产欧美一区二区三区r| 又爽又粗又大又长的爆草| 日本十八禁大骚逼| 综合伊人久久在一二三区| 男人的天堂久久久久久久| 一区二区三区 日韩在线| 日韩乱码一区二区三区中文字幕| 69国产精品久久久久久人| 在线观看日韩欧美| 国产乱色国产精品免费播放| 狠狠五月激情综合去干网| 2021最新热播国产一区二区| 黑人大鸡巴双插美女| 无遮挡粉嫩久久久久久久| 国产 欧美 日韩 黄片| 大鸡巴日大鸡巴在线观看| 无码爆一二三区免费视频| 2021国产一区二区岛国| 在线观看国产日韩欧美一区二区| 高颜值情侣鸡巴插插淫叫|