亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailboard balance cylinder Sold to Brazil

Release time:2023-11-08 10:36:59 Hits: Current position: Home > News

This article mainly introduces:

Brazil hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

Brazil tailboard balance cylinder

(Brazil tailboard balance cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tailboard balance cylinder are widely used in Brazil,because of excellent temperature resistance,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed tailboard balance cylinder for customers from Brazil.

Introduction to tailboard balance cylinder:

The pressure of the sliding surface of the tailboard balance cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the tailboard balance cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Do not enter foreign bodies when installing the tailboard balance cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

The machining accuracy of the tailboard balance cylinder depends on the level of equipment, production technology and testing means. tailboard balance cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular tailboard balance cylinder action. Troubleshooting method: Replace the rubber hose.

Answers to some questions about tailboard balance cylinder:

How is the hydraulic cylinder tempered?
The purpose of the tempering treatment is to make the piston rod have comprehensive mechanical properties of strength, hardness, plasticity and toughness, and the internal structure is uniform and fine tempered sorbite, so as to prepare the organization for subsequent surface quenching. The length of the long cylinder piston rod is 3800-4200, and the diameter is Φ90-Φ110mm, so its heating equipment uses a 150KW well resistance furnace or 600KW suspension continuous resistance heating furnace, and the temperature is controlled by two areas. Heat treatment process parameters: in the shaft furnace, a furnace is suspended with 4 pieces, the quenching heating temperature is 830±10℃, and after holding heat for 160min, it is divided into two times for quenching, and two pieces are quenched each time, and the circulating cooling water is used for cooling.

What is the reason why the hydraulic cylinder is not good at lifting?
There may be several situations 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
蜜臀AV无码国产精品尤物| 亚洲成国产人片在线观看| 女人被男人操到高潮视频| 亚洲国产日韩欧美高清片| 无码社区在线观看| 国产精品免费99久久久| 婷婷6月天丁香综合在线| 精品久久久久亚洲中文字幕| 嗯啊好大好想要视频| 中日韩中文字幕无码一本| 国产精品一区二区日本欧美| 精品福利一区二区三区在线观看| 国产女做a爱全免费视频| 欧美日韩一区精品一区精品| 鸡巴插进女人的逼里| 欧美伦禁片在线播放| 99久久久国产精品k影| 久久久精品欧美一区二区三免费| 天天天天天干夜夜夜夜夜操| 一级做a爱过程免费视频俩| 有关日本黄色录像的视频| 美女麻豆颜色光屁股眼子| 国产精品国产三级国| 亚洲二亚洲欧美一区vr| 国产黄片在线免费看| 老熟妇高潮一区二区高清视频| 日韩有码视频在线| 国产欧美一区二区精品久久久| 日韩乱码一区二区三区中文字幕| 操批在线观看视频| 国产午夜福利片无码视频| 一级风流国产片a级| 国产亚洲欧美日韩在线观看一区| 国产精品自在自线。| 欧美性一区二区三区五区| 一级特黄大片色欧美精品| 插插插插插插插插插插插| 可以免费看黄的香蕉视频| 大香蕉尹人97超级视频| 农村胖肥胖女人操逼视频| 伊人网在线免费视频|