亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailplate hydraulic cylinder Sold to Libya

Release time:2023-11-08 10:36:58 Hits: Current position: Home > News

This article mainly introduces:

Libya hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

Libya tailplate hydraulic cylinder

(Libya tailplate hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tailplate hydraulic cylinder are widely used in Libya,because of no need for deceleration device,long service life,smooth movement.So our company has designed tailplate hydraulic cylinder for customers from Libya.

Introduction to tailplate hydraulic cylinder:

If the tailplate hydraulic cylinder slips or crawls, please check whether there is astringency inside the tailplate hydraulic cylinder, because the internal parts of the tailplate hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the tailplate hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the tailplate hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Classification of tailplate hydraulic cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

The tailplate hydraulic cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure tailplate hydraulic cylinder can use 20 steel pipe, and the high pressure tailplate hydraulic cylinder can use 45 steel pipe.

tailplate hydraulic cylinder body inspection: The inner surface of the tailplate hydraulic cylinder and the piston seal are the main factors causing the leakage in the tailplate hydraulic cylinder, if the tailplate hydraulic cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the tailplate hydraulic cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

Answers to some questions about tailplate hydraulic cylinder:

How do hydraulic equipment and hydraulic cylinders maintain a certain pressure after pressing to a certain position?
There are several methods. 1. You can use a constant pressure variable pump to adjust the control pressure of the pump to the pressure required by the cylinder, so that when the cylinder is in place, the pump uses the minimum flow rate to maintain the pressure, and the system is more energy saving. 2. If the pressure is maintained for a short time, a hydraulic control check valve can be added to the oil inlet end of the cylinder to close the cylinder and maintain the pressure. If the volume of the cylinder is large, an accumulator can be added between the valve and the cylinder to maintain pressure for 10-30 minutes. 3. You can add a small flow pump, the large pump after unloading, the small pump has been running, specifically for maintaining pressure.

What is the difference between gas-hydraulic pressurized cylinder, pneumatic cylinder and oil cylinder?
The cylinder block is small and the force is large, constant speed and variable speed can be used (easy to change), the adjustment of the output is also convenient, and the freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Easy cylinder control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
呦交小u女国产精品99| 久久久三级黄片免费视频| 亚洲天堂成年人在线视频| 无码av一区二区大桥久未| 午夜性刺激在线视频免费| 美女大鸡操很多水在线看| 鸡巴插骚逼真舒服| 国产三级精品久久久久| 日韩有码视频在线| 咪咪爱一级特黄大片| 国产青青操骚货在线观看| 国产精品一区二区日本欧美| 正在播放老熟女人与小伙| 欧美成人3p视频| 最新免费高清无码片| 成人黄色网破处在线播放| 国产精品久久久久妇| 黑人大吊又操又添| 大鸡吧插美女嫩逼| 日韩av大片一区二区三区| 鸡巴插进缝里 日本| 日韩国产精品视频一区| 大鸡巴插入阴道视频| 国产一二三四五自产| 自拍偷拍视频颜射| 国产午夜爽爽爽男女免费动漫AV| 国产天堂网一区二区三区 | 日韩成人伦理片在线观看| 国产污污污在线观看视频| 少妇勾搭外卖员在线观看| 日韩久久中文字幕| 欧美男女舔逼舔鸡巴视频| 男人的下面进女人的下面在线观看| 欧美精品第一区二区三区| 91秦先生全集在线观看| 裸毛片视频在线视频| 成人久久久久久蜜桃免费| 裸体美女被操的啊啊直叫| 人妻在线系列一区二区三| 操女人大逼视频下载| 中文字幕人妻一区二区三区久久|