亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

single rack cylinder Sold to Turkmenistan

Release time:2023-12-05 14:27:16 Hits: Current position: Home > News

This article mainly introduces:

Turkmenistan hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder

Turkmenistan single rack cylinder

(Turkmenistan single rack cylinder,produced by Hengyu Hydraulic Cylinder Factory)

single rack cylinder are widely used in Turkmenistan,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed single rack cylinder for customers from Turkmenistan.

Introduction to single rack cylinder:

The single rack cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the single rack cylinder should pay attention to: the operation should be as far away from the single rack cylinder as possible, to avoid falling objects, knocking, rubbing the single rack cylinder coating. When cleaning the single rack cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the single rack cylinder when the oil temperature exceeds 70 ° C.

When the single rack cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

If the seal of the single rack cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and single rack cylinder, and the phenomenon of "pulling the single rack cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

The wear of the hard chromium plating layer of the single rack cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

Answers to some questions about single rack cylinder:

How to achieve hydraulic cylinder self-locking?
Hydraulic cylinder self-locking is divided into oil self-locking and mechanical self-locking. The oil self-locking is equipped with a valve to maintain pressure, so that the hydraulic oil of the cylinder does not return to the tank, and the oil chamber of the cylinder is filled with a certain pressure of oil. However, this pressure holding self-locking is not very safe and reliable, and the plunger will slowly return if there is a leak. Mechanical self-locking is to install a nut on the plunger of the cylinder, and when the cylinder rises to the required position, the nut on the cylinder plunger is rotated to the end, and the cylinder block is in contact, so that the plunger will be fixed to the required height. When it is necessary to relieve the pressure, screw the nut on again and let the plunger return to the position. This kind of cylinder has a special name, called self-locking hydraulic cylinder.

How to repair the bent oil cylinder correctly?
If the bending oil cylinder leaks, the most direct way is to replace the seal ring. Most of the sealing rings used by domestic bending machines are made in Taiwan and Japan, so the service life of the sealing ring is still relatively long. If the bending oil cylinder used by the customer leaks oil, then when replacing the seal ring, be sure to choose a high-quality and durable seal ring. In this way, the replaced cylinder will not leak oil for a long time.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
午夜国产三级一区二区三| 农村胖肥胖女人操逼视频| 国产裸模大尺度私拍视频| 国产精品操大屁股老淑女| 女人被大鸡吧操逼| 日本免费无码一区二区到五区| 国产中文字幕在线一区二区三区| 大鸡巴射精在小穴动漫版| 泡芙啪啪啪黄色污污| 看看美日韩操逼吧| 久久丁香花五月天色婷婷| 大鸡巴操小逼的视频| 日韩人妻无码中字一区二区| 正在播放老熟女人与小伙| 少妇精品久久久一区二区免费| 亚洲精品成人无码| 日本欧美人一区二区三区| 精品麻豆国产免费一区二区三区| 无码人妻丰满熟妇区精品| 日韩激情精品久久久一区二区| 国产精品久久久69粉嫩| 97精品人妻人人做人人爽| 欧美日韩精品视频在线第一区| 欧美亚洲另类天天综合网| 白虎鲍鱼抠逼免费看| 午夜福利国产三级片| 国产欧美日本韩国一区二区| 无码人妻免费一区二区三区| 美女被操的流水AV| 国产a一级毛片午夜剧院| 欧美精品一区二区三区四区五区| 国产亚洲精品一区久久| 老太太在丛林日老B| 午夜福利国产三级片| 大鸡巴猛插小穴视频| 快日我啊好爽日我逼| 东京热无码AV一区二区三区| 日韩人妻精品一区二区三区| 好爽轻点太大了太深了视频| 日韩欧美中文字幕国产精品| 女人被大鸡吧操逼|