亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

unidirectional cylinder Sold to Indonesia

Release time:2023-11-08 10:36:56 Hits: Current position: Home > News

This article mainly introduces:

Indonesia hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder

Indonesia unidirectional cylinder

(Indonesia unidirectional cylinder,produced by Hengyu Group)

unidirectional cylinder are widely used in Indonesia,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed unidirectional cylinder for customers from Indonesia.

Introduction to unidirectional cylinder:

The unidirectional cylinder should be vented: when the unidirectional cylinder is installed or parked for a long time to work again, the air will penetrate into the unidirectional cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the unidirectional cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the unidirectional cylinder, the oil is best entered and discharged from the highest point of the unidirectional cylinder. unidirectional cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

The scar on the sliding surface of the unidirectional cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the unidirectional cylinder wall. Therefore, before installation, these scars must be fully repaired.

When the initial action of the unidirectional cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the unidirectional cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

Do not enter foreign bodies when installing the unidirectional cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

Answers to some questions about unidirectional cylinder:

How to repair if hydraulic shears cylinder oil leakage?
The hydraulic cylinder is generally disassembled and the sealing ring is replaced. There are generally two ways to install the ends of the hydraulic cylinder. The larger hydraulic cylinder is mostly flanged disc type, which is screwed to the middle cylinder block by several bolts, the bolts are removed, and the cylinder head is slowly pulled out. The smaller hydraulic cylinder, the cylinder block and the head itself are threaded, and the rotating end cap can be removed from the cylinder block. If you do not understand the hydraulic cylinder, it is best to ask someone to deal with it. It is easy to damage the sealing ring and internal surface during disassembly.

Why does the hydraulic cylinder go up to the top and then slowly go down?
Leakage in the cylinder or the hydraulic valve that controls the cylinder, can be replaced and removed. Or add a pressure retaining valve to the hydraulic system to ensure pressure.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
校花内射国产麻豆欧美一区| 韩国无玛黄片毛片| 国产精品三级一区二区| 无码中文字幕免费一区二区三区| 欧美日韩一级视频| 嗯嗯嗯啊啊啊好湿好痒好多水视频| 亚洲国产成人久久成人52| 97人人澡人人爽人人揉| 玩弄邻居少妇呻吟11p| 捆绑调教白浆一区二区三区| 99国产精品一区二区| a一级毛片免费高清在线| —级v免费大片欧美| 性一交一乱一乱一区二区| 视频一区视频二区制服丝袜| 国产精品国产三级国| 欧美精品国产一区二区在线观看| 黄片观看骚货浪荡| 内射后入在线观看一区| 欧美性做爰片免费视频看| 亚洲高清中文字幕一区二区三区| 国产午夜福利视频第三区| 大鸡吧老外操中国逼| 大鸡巴操淫逼视频| 插插插插插插插插插插插| 大黑屌狂操骚逼视频| 操俄罗斯美女bb| 又爽又粗又大又长的爆草| 精彩欧美一区二区三区| 美国毛片亚洲社区成人看| 大鸡鸡插我骚逼视频| 中文字幕在线观看第二页| 留学生美女被大黑屌猛戳| 久久久国产系列丝袜熟女| 精品久久av免费一区二区三区| 亚洲av一区二区在线看| 波多野结衣高潮尿喷| 内射后入在线观看一区| AV无码超清破解版流出| 亚洲国产综合精品 在线 一区| 国产欧美亚洲一区二区三|