亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

cylinder with sensor Sold to Cote d 'Ivoire

Release time:2023-12-05 14:27:08 Hits: Current position: Home > News

This article mainly introduces:

Cote d 'Ivoire hydraulic cylinder,cylinder with sensor manufacturer,cylinder with sensor

Cote d 'Ivoire cylinder with sensor

(Cote d 'Ivoire cylinder with sensor,produced by Hebei Hengyu company)

cylinder with sensor are widely used in Cote d 'Ivoire,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed cylinder with sensor for customers from Cote d 'Ivoire.

Introduction to cylinder with sensor:

The assembly work of the cylinder with sensor has a great impact on the quality of the cylinder with sensor: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

How the cavitation of the cylinder with sensor is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the cylinder with sensor, resulting in corrosive damage to the parts.

The pressure of the sliding surface of the cylinder with sensor piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the cylinder with sensor must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

The cylinder with sensor can not be used as grounding electrode to avoid electric damage to the piston rod.

Answers to some questions about cylinder with sensor:

Why does the hydraulic cylinder rebound after the rod cavity is extended into place?
The reason is that after the rod cavity is extended into place, the rod cavity and the rodless cavity are connected, so that the cylinder moves towards the rod cavity. After connecting, it is equivalent to the hydraulic oil directly driving the cylinder with an area equal to the piston rod. After the end of this problem, it is estimated that the seal is not very good, and the two cavities are connected after the pressure is increased to a certain extent; Or there is a problem in the valve, so that the two chambers are connected after reaching a certain pressure. Other phenomena: If the load is increased to a certain extent, no matter which side of the solenoid valve is energized, the cylinder will move to the rod cavity.

How to distinguish the bucket cylinder from the bucket rod cylinder?
It can be distinguished according to its installation and connection: one end of the bucket cylinder is connected with the bucket; The rod cylinder is not connected to the bucket. The bucket refers to the bucket installed on the excavator. According to the working mode, it is divided into backhoe bucket and shovel bucket, the backhoe bucket is commonly used. The boom and bucket rod are working device of the excavator, usually called the big arm and the forearm, which are mainly used to control the digging and loading of the bucket. The arm connected to the frame is longer, so it is commonly known as the big arm, and its term is called the boom. The arms connected to the digging bucket are smaller, so they are commonly known as the lower arms, and the term is called the bucket rod, so they are commonly known as the big lower arms.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女逼男逼小穴小骚下载| 国产女做a爱全免费视频| 操女人b直播软件| 久久精品伦一区二区三区| 国产免费好大好硬| 在线视频观看一区| 日韩激情精品久久久一区二区| 久久久三级黄片免费视频| 很黄很爽的免费视频大全| 午夜性福福利视频一区二区三区| 日本欧美一区二区三区| 亚洲精品国产人久久| 我要操日本女人的逼| 夫妻性生活视频在线直播| 在线视频观看一区| 日本黄色美女射精| 欧美人与动人物A级| 久久一区二区三区精华液介绍| 女生小穴色色视频| 搞段B片黄色全免费看看| 丁香社区五月在线视频久| 蜜桃av噜噜一区二区三区免费| 女人被男人躁爽色欲国产| 我和两个老师的浮乱生活| 国产 推油 性爱| 欧美精品第一区二区三区| 老司机精品成人无码AV| 日本一区二区在线高清| 亚洲国产一区二区不卡在线资源| 亚欧日韩国产在线| 三级成人国产高清视频| 国产精品免费第一区二区| 国产午夜爽爽爽男女免费动漫AV| 国产美女色诱视频又又酱| 麻豆视频一级片在线观看| 丁香婷婷色婷婷粗大| 三级片手机在线视频| 女人182毛片a级毛片| 中文字幕在线观看第二页| 高清国产一区二区| 视频一区二区三区日韩视频|