亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Slovakia

Release time:2023-12-05 14:27:05 Hits: Current position: Home > News

This article mainly introduces:

Slovakia hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Slovakia stacker cylinder

(Slovakia stacker cylinder,produced by Hebei Hengyu company)

stacker cylinder are widely used in Slovakia,because of no transmission clearance,clever hydraulic energy conversion,powerful torque.So our company has designed stacker cylinder for customers from Slovakia.

Introduction to stacker cylinder:

When the stacker cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the stacker cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

The definition of the minimum stable speed refers to the minimum movement speed of the stacker cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the stacker cylinder that undertakes different work has different requirements for the minimum stable speed.

stacker cylinder hydraulic oil selection: The recommended working oil viscosity of the stacker cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

If the stacker cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the stacker cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow stacker cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the stacker cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the stacker cylinder includes the leakage caused by excessive wear of the stacker cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and stacker cylinder, and the phenomenon of "pulling the stacker cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

Answers to some questions about stacker cylinder:

Design a hydraulic cylinder, the inner diameter of the cylinder is 100mm, what size of piston rod is best used?
This involves how much speed ratio you need, that is, the area ratio of the rod cavity and the rodless cavity, if the weight is relatively large, it is recommended that the speed ratio choose 2, that is, the piston rod diameter choose 70mm, under normal circumstances, the speed ratio choose 1.46, the piston rod diameter choose 55mm. Of course, there are many factors that affect the diameter of the piston rod, such as stroke, stroke is too long, in order to stabilize the work of the hydraulic cylinder, its diameter also needs to choose a relatively large, sometimes even non-standard products, need to choose according to the actual situation.

What is the difference between single acting hydraulic cylinder and double acting hydraulic cylinder?
Single action hydraulic cylinder is a single direction force work, the return of the plunger depends on itself or the weight of the mechanism to return. The double acting hydraulic cylinder is mainly different from the extension and retraction of the piston (the thrust and tension of the saying), which are all operated by the action of liquid pressure.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
老司机午夜精品视频无码| 人妻少妇精品视频12p| 国产合区在线一区二区三区| 非洲人粗大长硬配种视频| 三级成人国产高清视频| 91kaobi视频在线| 亚洲午夜福利视频在线| 国产裸模大尺度私拍视频| 少妇被黑人到高潮喷出白浆| 精品国产99亚洲一区二区三区| 99热这里只有精品97| 狗狗大鸡巴狂操美女| 永久性日韩无码视频| 最新中文字幕av不卡高清| 三级成人国产高清视频| 三级片成人京东热五月天| 亚洲av熟妇高潮精品啪啪| 日韩欧美视频在线观看不卡| 男人大鸡巴操女人的大逼| 把女生操出水的视频| 女人操女人大逼大片| 亚洲大尺度无码无码专线一区| 鸡巴和逼中国美女| 国产裸模大尺度私拍视频| 韩国女主播一区二区视频| 无码毛片一区二区本码视频| 在线观看国产日韩欧美一区二区| 火辣美女的操大逼| 国产黄片在线免费看| 国产色哟哟精选在线播放| 亚洲 欧美 精品 高清| 我最爱操女人的骚逼| 国产成人亚洲精品在线看| 大鸡巴干小逼视频| 中文字幕一区二区 在线| 色老头av亚洲三区三区| 欧美另类在线观看| 视频在线观看一区@99| 92婷婷伊人久久精品一区二区| 男的鸡巴插女的视频| 亚洲一区二区三区大胆视频|