亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

garbage truck hydraulic cylinder Sold to Pakistan

Release time:2023-12-02 14:47:34 Hits: Current position: Home > News

This article mainly introduces:

Pakistan hydraulic cylinder,garbage truck hydraulic cylinder manufacturer,garbage truck hydraulic cylinder

Pakistan garbage truck hydraulic cylinder

(Pakistan garbage truck hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

garbage truck hydraulic cylinder are widely used in Pakistan,because of no need for deceleration device,long service life,smooth movement.So our company has designed garbage truck hydraulic cylinder for customers from Pakistan.

Introduction to garbage truck hydraulic cylinder:

The cavitation of the garbage truck hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the garbage truck hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the garbage truck hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

garbage truck hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the garbage truck hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

garbage truck hydraulic cylinders in series, parallel and series parallel. Series: In the garbage truck hydraulic cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the garbage truck hydraulic cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the garbage truck hydraulic cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the garbage truck hydraulic cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

Answers to some questions about garbage truck hydraulic cylinder:

What factors does the movement speed of the cylinder in the hydraulic system depend on?
The hydraulic system should be the piston movement in the cylinder, and the speed should also be the speed of the piston, according to the piston speed formula: v=4qm/pai*(D^2-d^2) where q is the flow rate of the input hydraulic cylinder, m is the volumetric efficiency of the hydraulic cylinder, D, d is the diameter of the piston and piston rod, because other factors are determined, the movement speed of the cylinder depends on the flow rate.

Where is the cylinder used? What is it used for? Can it be used in cars?
Cylinders can be used as actuator in hydraulic system. Such as hydraulic jacks, dump truck box lifting device, dodging (snow) machine loader bucket lifting device. Hydraulic cylinders are also widely used in car cranes. It's all about cars.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中文字幕你懂的av一区二区| 久久国产亚洲高清| 一级e片在线观看| 欧美激情在线播放第一页| 日韩免费一级a毛片在线播放一级| 久久久18禁一区二区网| 久久丁香花五月天色婷婷| 娇嫩的被两根粗大的np| 普通话大屌操小穴| 日韩人妻精品一区二区三区99| 美性中文网中文字幕91| 大鸡巴插我在线观看| 美女扒开腿让男人桶爽揉| 好想大鸡巴插进阴道视频| 泰国无码AV片在线观看| 被几个大屌老外轮操| 淫荡淫水逼操烂视频| 久久精品人人爽人人爽快| 亚洲卡通动漫第127页| 免费看黑人操逼视频| 丁香婷婷亚洲六月综合色| 无码人妻精品一区二区三区蜜桃| 亚洲精品成a人在线观看| 国产一国产一级毛片无码视频百度| 爆操大奶子美女视频| 少妇被黑人到高潮喷出白浆| 欧美黄色三级成人小视频| 大屌把女生逼逼操肿国产| 女人被大鸡吧操逼| 亚洲中文字幕在线无码一区二区| 精品久久久久中文字幕人| 午夜成人理论片在线观看| 国内揄拍国内精品| 美女被插入小穴涩涩视频| 看看美日韩操逼吧| 大鸡巴插入阴道视频| 国产一区二区三区精品片| 黄色三极片在线观看| 五月天国产成人免费视频| 99视频在线看免费视频| 女女同性女同1区二区三|