亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

garbage truck hydraulic cylinder Sold to Sudan

Release time:2023-11-28 10:55:31 Hits:132 Current position: Home > News

This article mainly introduces:

Sudan hydraulic cylinder,garbage truck hydraulic cylinder manufacturer,garbage truck hydraulic cylinder

Sudan garbage truck hydraulic cylinder

(Sudan garbage truck hydraulic cylinder,produced by Hengyu Group)

garbage truck hydraulic cylinder are widely used in Sudan,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed garbage truck hydraulic cylinder for customers from Sudan.

Introduction to garbage truck hydraulic cylinder:

garbage truck hydraulic cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the garbage truck hydraulic cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the garbage truck hydraulic cylinder. c. The garbage truck hydraulic cylinder seal is extruded, if the O-ring is obviously extruded at the garbage truck hydraulic cylinder seal, replace the garbage truck hydraulic cylinder seal.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the garbage truck hydraulic cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

If the garbage truck hydraulic cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

When installing the garbage truck hydraulic cylinder, the axial ends of the garbage truck hydraulic cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the garbage truck hydraulic cylinder, there is axial expansion. If the two ends of the garbage truck hydraulic cylinder are fixed, all parts of the garbage truck hydraulic cylinder will be deformed. When disassembling the garbage truck hydraulic cylinder, it is strictly forbidden to hammer the garbage truck hydraulic cylinder and the piston surface, such as the garbage truck hydraulic cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

Answers to some questions about garbage truck hydraulic cylinder:

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

What is a variable amplitude cylinder?
The type of variable amplitude cylinder is: double acting piston type cylinder, single acting plunger type cylinder, double acting two-stage telescopic cylinder. Double acting piston cylinder is the most common application. The oil cylinder has two oil outlets, and when the oil is fed into the A port, the oil is returned to the B port; If the oil inlet of the B port is returned to the oil of the A port, the reciprocating movement of the piston depends on the effect of pressure. Single-acting plunger (or piston) cylinder has only one oil port, the pressure oil can only supply oil to one side of the plunger in the cylinder, the plunger moves in one direction under the action of pressure oil, and the return stroke of the plunger is driven by the gravity of the lifting arm, such as the LT1040 truck crane variable amplitude cylinder. The double-acting two-stage telescopic cylinder is a set structure, and the two-stage piston rod is like a tie rod antenna set in the cylinder barrel.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
久久综合色鬼综合色| 精品一区二区三区乱码中文字幕| 大黑鸡巴操模特骚B| 久久69精品久久久久免| 成人精品视频区一区二区三| 女教师色色天天免费播放| 99爱这里只有精品| 成人精品视频区一区二区三| avtt天堂网先锋伦理| 男女边吃奶边做边爱视频| 免看一级a一片成人欧美| 青青视频在线人视频在线| 女生的鸡鸡色色软件| 亚洲av 又黄又爽十大| 男插女逼啪啪啪软件| 中文字幕人妻一区二区三区久久| 操美女干逼调教捆绑视频| 亚洲乱熟女一区二区三区| 黑人大吊性交啪啪啪| 中文字幕一高清免费视频| 春宵福利导航91| 天美传媒精品1区2区3区| 999精品免费视频| 被下药强奷到舒服的视频| 大鸡巴操淫逼视频| 黑大吊肏小騷逼噴水| 美女嫩逼插进大屌| 呦交小u女国产精品99| 国产羞羞的视频在线观看| 中文字幕乱码一区三区免费| 国产女做a爱全免费视频| 国奴精品毛片av一区二区三区| 国产乱理伦片在线观看夜| 欧美一区二区高清视频在线观看| 最新AV中文字幕在线看| 欲色欲香天天网综合久久| 无码人妻精品一区二区三区蜜桃| 男女边吃奶边做边爱视频| 2021国产一区二区岛国| 性色av一区二区三区天美传媒四| 小美女淫荡的视频|