亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reciprocating cylinder Sold to Czech Republic

Release time:2023-11-28 10:55:14 Hits: Current position: Home > News

This article mainly introduces:

Czech Republic hydraulic cylinder,reciprocating cylinder manufacturer,reciprocating cylinder

Czech Republic reciprocating cylinder

(Czech Republic reciprocating cylinder,produced by Hengyu Group)

reciprocating cylinder are widely used in Czech Republic,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed reciprocating cylinder for customers from Czech Republic.

Introduction to reciprocating cylinder:

The wear of the hard chromium plating layer of the reciprocating cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

When the reciprocating cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the reciprocating cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil reciprocating cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical reciprocating cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the reciprocating cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the reciprocating cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The reciprocating cylinder is not the same as the reciprocating cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the reciprocating cylinder can not be used as a high-power power component, but the reciprocating cylinder can be used as a relatively large power component, or the reciprocating cylinder system can be used.

Answers to some questions about reciprocating cylinder:

How to disassemble injection molding machine injection cylinder?
If it is not repaired for a long time, it is recommended to open both ends, comprehensively check the oil seal and piston ring inside, this is not much difficulty, pay attention to not install reverse when changing the oil seal, some piston rings are steel rings are rubber rings, and several interfaces of steel rings are not in the same position; Rubber ring pay attention not to install reverse; Be careful not to damage the oil seal when installing, otherwise it will soon leak oil.

Two cylinders in parallel, how to solve the synchronization problem?
The following methods can be used to achieve parallel cylinder synchronization: 1, rigid mechanical synchronization. 2. The throttle valve or speed regulating valve is used in the circuit to adjust the synchronization. 3, the two cylinders use independent quantitative pump oil supply to achieve synchronization. 4. Synchronous motor is used in the loop to realize cylinder synchronization. 5, using the position sensor to measure the stroke position and control the cylinder synchronization through the electrical system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
在线视频观看一区| 国产精选三级在线观看| 中文字幕亚洲欧美精品一区二区| 欧美亚洲干妞内射| 久久久久久久久黄片观看| 美女被插进去黄色| 啊啊好想被大鸡巴操视频| 国产妇女乱一性一交| 欧美性做爰片免费视频看| 国产乱精品一区二区三区视频了| 在线观看国产日韩欧美一区二区| 黑人大屌爆操骚货| 国产精品免费第一区二区| 日本不卡高清视频在线播放| 操国产骚逼逼逼逼逼逼逼| 国产合区在线一区二区三区| 97性无码区免费| 男人操女人下面国产剧情| 久久久中文字幕在线视频| 日韩美女黄大片在线观看| 久久高清中文字幕第一页| 久久久一区二区三区日本| 欧美日韩综合在线一区| 国产 推油 性爱| 捆绑调教白浆一区二区三区| 亚洲中文字幕二区不卡| 中文字幕在线观看第二页| 国产羞羞的视频在线观看| 国产精品碰碰现在自| 日本欧美一区二区三区| 精品人妻少妇一区二区三区不卡| 老色鬼精品视频二区三区| 亚洲国产成人久久成人52| 丁香婷婷色婷婷粗大| 中文无码av动作片| 亚洲天堂av一区二区在线观看| 天堂无码不卡av| 亚洲中文字幕在线无码一区二区| 西西大尺度无码免费视频| 裸体美女被操的啊啊直叫| 狠狠干无码日韩AV|