亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Algeria

Release time:2023-11-28 10:55:13 Hits: Current position: Home > News

This article mainly introduces:

Algeria hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Algeria swager cylinder

(Algeria swager cylinder,produced by Hengyu Hydraulic Co., Ltd)

swager cylinder are widely used in Algeria,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed swager cylinder for customers from Algeria.

Introduction to swager cylinder:

swager cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the swager cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

In recent years, the processing process of the swager cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

When the swager cylinder is in use, ensure that the swager cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

The assembly work of the swager cylinder has a great impact on the quality of the swager cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Answers to some questions about swager cylinder:

What does cylinder hob125*100 mean?
HOB is a series of hydraulic cylinder products, the use of pressure 14MPA, tie rod structure. 125 refers to the diameter of the cylinder and 100 refers to the stroke. The unit is millimeters.

How does the variable amplitude cylinder work?
The variable amplitude cylinder is generally an engineering hydraulic cylinder connected by the front and back earrings, and the telescopic expansion of the hydraulic cylinder changes the Angle of the arm of the lifting machinery to achieve the role of the variable amplitude, according to the role it plays is called the variable amplitude cylinder, and there is no variable amplitude hydraulic cylinder in the classification of hydraulic cylinders.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
色综合久久久久综合激情| 久久久久人妻精品明星换脸| 国产高新无码在线观看| 欧美日韩激情精品久久久久久| 欧美精品专区一区二区| 国产资源网中文最新版| 激情久久三级视频网站| 国产r级亚洲r级在线观看| 国产黄在线视频免费| 精品久久久久久久久久中文幕| 97国产精品国偷自产在线| 日本韩国亚洲欧美一区二区三区| 精品国产_亚洲人成在线| 人人爽人人爽人人妻av| 国产69精品一区二区三区| 精品久久久久一区二区三| 欧美色到久久88综合亚洲精品| 97久久人人超碰国产精品| 国产v亚洲v天堂无码| 婷婷色婷婷开心五月四房播播| 日韩欧美亚洲中文字幕区在高我| 国产一区二区三区网址| 欧美精品在线观看不卡| 国产一区二区三区欧美日| 国产一级精品无码免费视频| 国产精品日本欧美一区二区三区| 日韩欧美一区中文字幕在线| 久久中文字幕一区不卡| 伊人精品久久久久7777| 亚洲区一区二区三区视频| 国产一区二区日本在线观看| 日韩一区二区人妻9999| 久久久久久999一区二区三区| 国内精品国产三级国产av万事达| 亚洲成人情色综合网| 久久久久久亚洲一区二区| 欧美日韩一级裸体黄色视| 中文字幕日韩欧美推理片免费观看| 国产精品久久久久久妇女| 欧美日韩国产成人精品自拍视频| 黑人操亚洲女一级黄色片|