亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steering power cylinder Sold to Thailand

Release time:2023-11-08 10:36:39 Hits: Current position: Home > News

This article mainly introduces:

Thailand hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

Thailand steering power cylinder

(Thailand steering power cylinder,produced by Hengyu Hydraulic Co., Ltd)

steering power cylinder are widely used in Thailand,because of excellent fatigue and impact resistance,long service life,no need for deceleration device.So our company has designed steering power cylinder for customers from Thailand.

Introduction to steering power cylinder:

When the steering power cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the steering power cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil steering power cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical steering power cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the steering power cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

How to determine the working pressure of the steering power cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, steering power cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

The internal leakage of the steering power cylinder should be prevented when the steering power cylinder is used. The internal leakage of steering power cylinder includes the leakage caused by excessive wear of steering power cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

If the steering power cylinder slips or crawls, please check whether there is astringency inside the steering power cylinder, because the internal parts of the steering power cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the steering power cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the steering power cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Answers to some questions about steering power cylinder:

How to repair if hydraulic shears cylinder oil leakage?
The hydraulic cylinder is generally disassembled and the sealing ring is replaced. There are generally two ways to install the ends of the hydraulic cylinder. The larger hydraulic cylinder is mostly flanged disc type, which is screwed to the middle cylinder block by several bolts, the bolts are removed, and the cylinder head is slowly pulled out. The smaller hydraulic cylinder, the cylinder block and the head itself are threaded, and the rotating end cap can be removed from the cylinder block. If you do not understand the hydraulic cylinder, it is best to ask someone to deal with it. It is easy to damage the sealing ring and internal surface during disassembly.

How to distinguish the size of hydraulic cylinder cavity?
The hydraulic cylinder has a rod cavity and a rodless cavity. The rod cavity is the cavity that the piston rod extends out. The rod cavity is of course small due to the existence of the piston rod. That's just relative.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品精品国产一区二区性色av| 亚洲欧洲精品无码久久久| 日本一区二区在线高清| 3色w九九久久男人皇宫宕| 国内精品久久久久精品97| 快日我啊好爽日我逼| 亚洲大尺度无码无码专线一区| 大鸡巴插入骚穴在线观看| 美女扒开腿让男人桶爽揉| 交换夫妇4中文字幕| 欧美亚洲综合一区二区三区| 欧美日韩精品视频在线第一区| 娇嫩的被两根粗大的np| 鸡巴插进缝里 日本| av中文字幕一区二区精品久久| 大鸡巴抽插小穴色虐视频| 久久久精品欧美一区二区三免费| 96精品久久久久久蜜臀浪| 美女主播被操流水| 91久国产在线观看| 大狼狗插阴道视频| 大鸡巴干小逼视频| 色网女人日本逼欧美| 干美妞肛门在线播放| 男女插插调教骚逼| 男生操女生无马赛克免费| 欧美高清一二三区| 亚洲乱熟女一区二区三区| 男生鸡鸡插进女生笑穴里| 国产 日韩 亚洲 一区| 免看一级a一片成人欧美| 快速了解国产一级a爱片| 大黑屌日本另类肛交| 那种视频在线观看你懂的| 日本入室强伦姧人妻中文| 免费骚逼潮吹av| 国产精品久久一区二区三区动| 亚洲精品国产人久久| 中文字幕av一区二区三区蜜桃| 国产黄片在线免费看| 99爱国产精品免费视频|