亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

series synchronous cylinder Sold to Croatia

Release time:2023-11-27 15:08:44 Hits: Current position: Home > News

This article mainly introduces:

Croatia hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

Croatia series synchronous cylinder

(Croatia series synchronous cylinder,produced by Hengyu Group)

series synchronous cylinder are widely used in Croatia,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed series synchronous cylinder for customers from Croatia.

Introduction to series synchronous cylinder:

The coordination of the sliding parts of the series synchronous cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

When the series synchronous cylinder is installed, the piston and the series synchronous cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the series synchronous cylinder head boss is easy to cause scars when it hits the inner surface of the series synchronous cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized series synchronous cylinders, only careful and careful operation can be avoided.

When the oil pressure of the series synchronous cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

The pressure of the sliding surface of the series synchronous cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the series synchronous cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Answers to some questions about series synchronous cylinder:

Why manual forklift oil cylinder can not lift up?
Manual hydraulic forklift truck often can not be pressed up, there are several reasons: for manual hydraulic truck: 1) There is no hydraulic oil 2) the purity of the oil is not enough 3) the adjusting bolt is too close or the adjusting screw is too tight, so that the valve is always open, 4) there is an air in the hydraulic cylinder. Method: 1) Refueling 2) Oil change 3) air discharge. For manual hydraulic stacker, also called manual lift car 1) Less than the amount of oil 2) impurities in the hydraulic oil, so that the check valve can not be closed. Method 1) Add enough hydraulic oil 2) Remove the cylinder, screw off the bottom plate, remove the impurities in the bottom plate.

Is it normal for the cylinder to turn black?
Cylinder blackening is a soft fault: 1. It does not affect the normal operation of your equipment. 2. Cylinder blackening involves a lot of things: hydraulic oil, oil seal material, piston rod coating, etc. These three things are not determined by the manufacturer because these three things are provided by other manufacturers. If the equipment is not due to high temperature caused by the black cylinder, you do not have to worry too much because your excavator can still work normally. If you feel uncomfortable, you can choose to replace the cylinder or replace the hydraulic oil.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
性色av一区二区三区天美传媒四| 97人人澡人人爽人人揉| 中国熟女色av夜夜嗨| 中文字幕精品字幕一区二区三区| 欧美日韩一级视频| 美女被大屌操大骚逼| 欧美高清一二三区| 从后面狠狠的干白嫩少妇| 中日韩中文字幕无码一本| 久久综合日韩亚洲精品色| 国产 日韩 亚洲 一区| 骚穴 操我 视频| 日韩高清精品一区有码在线| 西西大尺度无码免费视频| 中文字幕一区二区日韩精品蜜臂| 国产精品自在自线。| 翘臀小穴在线观看| 三级片成人京东热五月天| 亚洲 自拍 欧美 一区| 无遮挡粉嫩久久久久久久| 久久69精品久久久久免| 最新黄色A级一短片| 韩国无遮挡成人免费视频| 激烈18禁高潮视频免费| 日本免费精品一区二区三区四区| 免费看黑人操逼视频| 亚洲一区二区三区四区国产| 亚洲精品伦理熟女国产| 欧美性一区二区三区五区| 非洲大鸡巴操逼黄色录像| 中文字幕av一区二区三区蜜桃| 日本欧美人一区二区三区| 日本成人在线一区中文字幕| 下载风骚美女想吃大机吧| 国产综合精品一区二区青青| 亚洲欧美日韩清纯唯美第一区| 中国老女人 操逼 视频| 操纯欲女生小穴视频| 亚洲综合极品香蕉久久网| 啊啊啊好疼视频进来| 亚洲AV天堂一区二区香蕉|