亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Nepal

Release time:2023-11-08 10:36:36 Hits: Current position: Home > News

This article mainly introduces:

Nepal hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Nepal trunnion cylinder

(Nepal trunnion cylinder,produced by Hengyu Hydraulic Cylinder Factory)

trunnion cylinder are widely used in Nepal,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed trunnion cylinder for customers from Nepal.

Introduction to trunnion cylinder:

When the trunnion cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the trunnion cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil trunnion cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical trunnion cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the trunnion cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

When the hydraulic oil is not pumped into the trunnion cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the trunnion cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

The trunnion cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the trunnion cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the trunnion cylinder wall due to the stiffness and the weight of the parts, causing scars.

When purchasing the trunnion cylinder, try to clarify the following parameters of the trunnion cylinder: A. trunnion cylinder diameter, rod diameter, stroke; B. Working pressure or trunnion cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right trunnion cylinder type can be found accurately and quickly.

Answers to some questions about trunnion cylinder:

How to judge the leakage in the cylinder?
Common judgment method: In the production site, people make full use of watching, listening, smelling, touching and other sensory ways, by observing that the cylinder can not move or delay the action or feel the oil temperature change, vibration and noise, etc., and then judge whether the cylinder has internal leakage according to experience. Another method commonly used in the field is to extend the cylinder in place to ensure that the cylinder does not have any load and will not retract (to prevent the cylinder from internal leakage accidents), turn off the machine, and then remove the tubing with the rod cavity, and then press the switch that pulls out the cylinder (do not press the wrong switch). If the oil nozzle with the rod cavity drains the cylinder internally, If there's no oil coming out, you have to think about something else going wrong.

Why does the tipping bucket cylinder have a cylinder withdrawal problem?
This problem may have a certain relationship with the operation of the driver, the main reasons are the following two situation analysis: 1, the current domestic loader working device is mostly a six-link mechanism, the six-link mechanism in the bucket to the limit position, lift the boom, the rotating bucket cylinder will appear "cylinder pulling" phenomenon, that is, the piston rod of the rotating bucket cylinder will be pulled out. In this case, in order to protect the cylinder, a pressure overload protection valve with large and small cavities is provided on the multi-way valve rotating bucket link (large chamber 18MPa, small chamber 12MPa). 2, before the cylinder is assembled to the whole machine, the cylinder is not limited, the piston rod of the cylinder can be pulled in place before and after, but when it is installed on the whole machine, in order to avoid the cylinder pulling out, the limit switch is installed according to the regulations.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
可以免费看污污片的软件| 亚洲激情无码视频| 日本精品久久不卡一区二区| 护士毛片在线看中文字幕| ai换脸久久一区二区亚洲av| 日本潘金莲三级bd高清| 久久久国产精品2020| 黄色三极片在线观看| 国产亚洲一区二区手机在线观看| 中文国产成人精品久久久| 欧美日韩一区精品一区精品| 爆乳1把你榨干在线观看| 国产欧美一二区不卡视频| 性色av少妇一区二区三区多人| 日韩毛片一区视频免费在线观看| 欧美黄色三级成人小视频| 女女同性女同1区二区三| 最新的亚洲欧美中文字幕| 亚洲av午夜一区二区| 欧美办公室大鸡巴| 亚洲高清中文字幕一区二区三区| 大鸡吧视频在线观看| 国产在线中文字幕一区二区三区| 欧美日韩欧美国产中文字幕| 亚洲男人的天堂2021| 操美女逼逼色逼网| 国产精品免费99久久久| 91午夜福利1000集| 欧美大鸡巴操大骚逼| 熟妇人妻无乱码中文字幕| 白色紧身裤无码系列在线| 让女人下面出水视频| 大鸡巴操屁眼无码| 可以免费看黄的香蕉视频| 中文字幕亚洲欧美精品一区二区| 被医生添奶头和下面好爽| 色哟哟精品视频一区二区| 日韩欧美中文字幕国产精品| av中文字幕一区二区精品久久| 在线观看国产黄色| 大黑屌日本另类肛交|