亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Malaysia

Release time:2023-11-27 15:08:32 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Malaysia stern plate hydraulic cylinder

(Malaysia stern plate hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stern plate hydraulic cylinder are widely used in Malaysia,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed stern plate hydraulic cylinder for customers from Malaysia.

Introduction to stern plate hydraulic cylinder:

The scar on the sliding surface of the stern plate hydraulic cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the stern plate hydraulic cylinder wall. Therefore, before installation, these scars must be fully repaired.

The internal leakage of the stern plate hydraulic cylinder should be prevented when the stern plate hydraulic cylinder is used. The internal leakage of stern plate hydraulic cylinder includes the leakage caused by excessive wear of stern plate hydraulic cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular stern plate hydraulic cylinder action. Troubleshooting method: Replace the rubber hose.

stern plate hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching stern plate hydraulic cylinder block - fine boring stern plate hydraulic cylinder block - grinding stern plate hydraulic cylinder block. The rolling method is: broaching stern plate hydraulic cylinder block - fine boring stern plate hydraulic cylinder block - rolling stern plate hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the stern plate hydraulic cylinder block is about 1-2 days, rolling 1 meter of the stern plate hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the stern plate hydraulic cylinder increases by 25%. If the stern plate hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality stern plate hydraulic cylinders, you must take the rolling production process. After the stern plate hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

Answers to some questions about stern plate hydraulic cylinder:

What's a minus 40 cylinder made of?
Construction with 1Cr18Ni9Ti, in low temperature conditions impact and tensile strength are very good, can withstand -100 degrees of low temperature, corrosion resistance, material price is not very high, more economic.

Design a hydraulic cylinder, the inner diameter of the cylinder is 100mm, what size of piston rod is best used?
This involves how much speed ratio you need, that is, the area ratio of the rod cavity and the rodless cavity, if the weight is relatively large, it is recommended that the speed ratio choose 2, that is, the piston rod diameter choose 70mm, under normal circumstances, the speed ratio choose 1.46, the piston rod diameter choose 55mm. Of course, there are many factors that affect the diameter of the piston rod, such as stroke, stroke is too long, in order to stabilize the work of the hydraulic cylinder, its diameter also needs to choose a relatively large, sometimes even non-standard products, need to choose according to the actual situation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
激情久久久久久久久久久| 国产 日韩 亚洲 一区| 欧美一区二区三区四公司| 国产美女裸体视频全免费| 在线12萝自慰喷水| 久久久中文字幕一区| 操逼啊 啊 啊黄色视频| 18岁美女破处在线观看| 日本一区二区高清免费不卡| 国产裸模大尺度私拍视频| 91孕妇精品一区二区三区| 综合欧美日韩一区二区三区| 中文字幕乱码一区三区免费| 美女逼男逼小穴小骚下载| 夫妻性生活视频在线直播| 日韩人妻精品一区二区三区| 大逼女人污污视频| 一级特黄大片色欧美精品| 成人久久久久久蜜桃免费| 欧美性爱撅臀插入啪啪啪| 欧美一区二区高清视频在线观看| 男生舔女生下面黄色视频| 一区二区三区 日韩在线| 国产精选三级在线观看| 美性中文网中文字幕91| 天天干天天操天天插| 高清最新操逼吃鸡巴视频| 国产高清乱码女大生AV| 挺进绝色邻居的紧窄小肉| 日本老熟妇毛茸茸| 国产无圣光一区福利二区| 少妇毛片一区二区三区免费视频| 欧美精品一区二区三区四区五区| 美国大骚逼啊啊啊| 国产A级黄片下载| 欧美巨屌虐无毛骚逼| 午夜国产精品午夜福利网| 亚洲国产精品一区亚洲国产| 久久亚洲精品中文字幕一| 蜜臀AV无码国产精品尤物| 国产女做a爱全免费视频|