亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reciprocating cylinder Sold to Malaysia

Release time:2023-11-26 09:50:20 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,reciprocating cylinder manufacturer,reciprocating cylinder

Malaysia reciprocating cylinder

(Malaysia reciprocating cylinder,produced by Hebei Hengyu company)

reciprocating cylinder are widely used in Malaysia,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed reciprocating cylinder for customers from Malaysia.

Introduction to reciprocating cylinder:

After chrome plating of the piston rod of the reciprocating cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

There are some honeycomb holes in the inner wall of the reciprocating cylinder, piston or piston rod surface. How is this formed? When we repair the reciprocating cylinder, we can see that there are some honeycomb holes on the inner wall of the reciprocating cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the reciprocating cylinder is targeted to prevent. Is very necessary.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the reciprocating cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

In the process of using the reciprocating cylinder, sometimes such a problem will occur, the reciprocating cylinder can not act immediately after the instruction of the reciprocating cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil reciprocating cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

Answers to some questions about reciprocating cylinder:

How to distinguish cylinder rod head and cylinder bottom?
One end of the piston rod can be telescopic is the rod head, and the one behind is the bottom of the cylinder, which is the single rod cylinder.

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
91精品国产综合久久久福利| 久久久久久精品无码免费看| 国产精品va在线观看老妇女| 日本在线观看黄视频| 久久久久国产精品老熟女| 久久婷婷综合激情亚洲狠狠| 中文字幕熟女一区二区三区| 成人一级片黄色一级片| 国产精品v欧美精品v日本精| 国产精品观看不卡视频| 亚洲综合网无码中文字幕| 亚洲色无码专区在线观看精品| 白嫩丰满少妇一区二区| 中文人操人人插人免费看视频| 9久久99久久久免费精品然| 亚洲成人蜜桃动漫一区| 亚洲成人情色综合网| 婷婷色婷婷开心五月四房播播| 五月婷婷六月丁香综合小说| 日韩精品视频在线观看一区二区三区| 亚洲精品国产成人99久久6| 欧洲在线观看亚洲三区| 久久综合视频中文字幕| 日本边添边摸边做边爱喷水| 欧美日韩永久精品一区二区| 日本韩国亚洲欧美一区二区三区| 欧美日韩国产综合在线视频| 欧美日韩成人精品大片| 在线观看福利中文字幕| 日本伊人久久精品视频| 国产精品日本欧美一区二区三区| 爆操小骚货在线观看| 亚洲欧美中文在线另类| 久久久精品视频地址| 日韩精品一区二区av蜜桃| 无码无套少妇毛多69XXX| 中文字幕日本一区二区在线观看| 国产69精品一区二区三区| 欧美精品在欧美一区二区三区| 国产r级亚洲r级在线观看| 国产欧美在线观看精品一区污|