亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

roller press hydraulic cylinder Sold to Thailand

Release time:2023-11-26 09:50:13 Hits: Current position: Home > News

This article mainly introduces:

Thailand hydraulic cylinder,roller press hydraulic cylinder manufacturer,roller press hydraulic cylinder

Thailand roller press hydraulic cylinder

(Thailand roller press hydraulic cylinder,produced by Hebei Hengyu company)

roller press hydraulic cylinder are widely used in Thailand,because of simple structure and reliable operation,excellent temperature resistance,clever hydraulic energy conversion.So our company has designed roller press hydraulic cylinder for customers from Thailand.

Introduction to roller press hydraulic cylinder:

How the cavitation of the roller press hydraulic cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the roller press hydraulic cylinder, resulting in corrosive damage to the parts.

roller press hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the roller press hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

roller press hydraulic cylinder daily maintenance, should focus on checking whether the piston rod surface roughness and shape and position tolerance meet the technical requirements, if the piston rod bending should be calibrated to meet the requirements or according to the physical mapping, manufactured by a professional manufacturer. If the piston rod surface coating wear, slip damage, local spalling can be adopted to remove the coating, re-chrome surface processing process.

The roller press hydraulic cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the roller press hydraulic cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the roller press hydraulic cylinder wall due to the stiffness and the weight of the parts, causing scars.

Answers to some questions about roller press hydraulic cylinder:

100 tons press, the cylinder diameter is 250, how much pressure?
100 tons hydraulic press, if it is a single acting hydraulic cylinder, the required oil pressure is the nominal force divided by the cross-sectional area of the cylinder piston. One hundred tons of its pressure is 1000 kN (1000000N), the diameter of the cylinder is 250 mm, its area is the circular rate multiplied by the square of the radius, is 49062.5 square mm, and then the pressure divided by the area of the oil pressure is 20.38MPa. Therefore, a hydraulic pressure of 20.38 mpa is required for a 250 diameter cylinder to obtain 100 tons of pressure.

What are the requirements for hydraulic cylinder assembly? ① The installation of the cylinder should be solid and reliable. In order to prevent the influence of thermal expansion, in the case of large stroke and hot working conditions, one end of the cylinder must be kept floating.② pipe connection shall not be relaxed.③ The mounting surface of the hydraulic cylinder and the sliding surface of the piston rod should maintain sufficient parallelism and perpendicality.④ The central axis of the moving cylinder should be concentric with the center line of the load force, otherwise it will cause lateral force, which is easy to wear the seal And piston damage. The greater the distance between the supporting points of the piston rod, the smaller its wear. For the hydraulic cylinder of the moving object, the installation should keep the cylinder parallel with the moving object, and the degree of non-parallelism is generally not greater than 0.05mm/m. ⑤The sealing ring should not be installed too tightly, especially the U-shaped sealing ring.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品熟女一区二区三区久久夜| 日本免费无码一区二区到五区| 帅哥大鸡巴操美女| 大鸡巴射精在小穴动漫版| 91精品国产综合久久久蜜| 美女麻豆颜色光屁股眼子| 国产精品熟女视频播放| 日韩激情精品久久久一区二区| 24日本精品视频免费| 欧美 日本 亚洲 国产| 久久亚洲精品中文字幕一| 日本免费一区二区在线| 亚洲日韩不卡一区二区三区| 欧洲美熟女乱又伦| 男生用鸡巴操女生的视频| 市长含着秘书的奶头| 大黑屌狂操骚逼视频| 大阴茎交于大阴户黄片视频| 久久久久有精品国产麻豆| 99久久久国产精品k影| 亚洲福利小视频在线观看| 我要看成人免费毛片| 欧美一区二区三区久久国产精品| 日韩乱码一区二区三区中文字幕| 巨屌抽插舔阴视频| 尤物性生活午夜在线视频| 丁香婷婷亚洲六月综合色| 这里只有久久精品| 国内精品久久久久精品97| 亚洲国产精品伦理在线看| 91午夜福利1000集| av人摸人人人澡人人超| 国产精品一区二区三区涩涩av| 亚洲精品自拍偷拍第一页| 99热这里有精品在线观看| 国产精品一区二区日本欧美| 97人妻精品一区二区三区视频| 夫妻性生活视频在线直播| 日本 日韩 欧美| 一区二区三区国产l精品欧美| 国产女主播喷出白浆视频|