亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

100 ton hydraulic cylinder Sold to Ireland

Release time:2023-11-26 09:50:05 Hits: Current position: Home > News

This article mainly introduces:

Ireland hydraulic cylinder,100 ton hydraulic cylinder manufacturer,100 ton hydraulic cylinder

Ireland 100 ton hydraulic cylinder

(Ireland 100 ton hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

100 ton hydraulic cylinder are widely used in Ireland,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed 100 ton hydraulic cylinder for customers from Ireland.

Introduction to 100 ton hydraulic cylinder:

There are some honeycomb holes in the inner wall of the 100 ton hydraulic cylinder, piston or piston rod surface. How is this formed? When we repair the 100 ton hydraulic cylinder, we can see that there are some honeycomb holes on the inner wall of the 100 ton hydraulic cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the 100 ton hydraulic cylinder is targeted to prevent. Is very necessary.

100 ton hydraulic cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the 100 ton hydraulic cylinder head itself is the guide sleeve of the piston rod, the 100 ton hydraulic cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the 100 ton hydraulic cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

The pressure of the sliding surface of the 100 ton hydraulic cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the 100 ton hydraulic cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

The 100 ton hydraulic cylinder is not the same as the 100 ton hydraulic cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the 100 ton hydraulic cylinder can not be used as a high-power power component, but the 100 ton hydraulic cylinder can be used as a relatively large power component, or the 100 ton hydraulic cylinder system can be used.

Answers to some questions about 100 ton hydraulic cylinder:

When the hydraulic cylinder changes from fast to slow, how can the slow speed become more even and the speed can be adjusted?
Reversing valve set 2 reversing valves. The back of one valve goes directly to the cylinder, running at full speed for fast action. Add a speed control valve behind the other valve, and then connect to the cylinder to achieve slow action, you can adjust the opening of the speed control valve, to achieve the speed of the cylinder can be adjusted. An import speed control valve to more than 1,000 yuan, if you think it is too expensive, you can also use the throttle valve instead. However, the throttle valve is greatly affected by the load change.

Why does the hydraulic cylinder rebound after the rod cavity is extended into place?
The reason is that after the rod cavity is extended into place, the rod cavity and the rodless cavity are connected, so that the cylinder moves towards the rod cavity. After connecting, it is equivalent to the hydraulic oil directly driving the cylinder with an area equal to the piston rod. After the end of this problem, it is estimated that the seal is not very good, and the two cavities are connected after the pressure is increased to a certain extent; Or there is a problem in the valve, so that the two chambers are connected after reaching a certain pressure. Other phenomena: If the load is increased to a certain extent, no matter which side of the solenoid valve is energized, the cylinder will move to the rod cavity.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
24日本精品视频免费| 国产精品午夜小视频观看| 日本欧美人一区二区三区| 日本成人在线一区中文字幕| 国产一区二区在线观看精品| 黑人大吊又操又添| 亚洲一区二区三区大胆视频| 国产精品熟女视频播放| 五月天亚洲激情综合av| 被大鸡巴操淫液视频| 插欧美美女逼逼逼逼| 被大鸡巴操淫液视频| 欧美一区二区三区久久国产精品| 欧美日韩亚洲人人夜夜澡| 八插8插黄色视频| 嗯啊好大好想要视频| 人妻熟女av一区二区三区| 18岁美女破处在线观看| 国产三级精品久久久久| 野外日逼视频免费看| 淫荡扣逼骚逼视频| 人妻少妇精品视频12p| 国产成人AV剧情| 日本二区在线观看| 上萬網友分享a级国产乱| 99精品一级欧美片免费| 中文无码av动作片| 枫花恋精品一区二区久久| 国产午夜高清无码一级片| 大吊肏子宫在线观看| 搞段B片黄色全免费看看| 操逼动漫首页登录| 在线观看国产日韩欧美一区二区| 亚洲欧美国产原创一区二区三区| 九九视频免费在线观看| 黄色软件大屌怒戳粉嫩小穴| 女人日比比视频免费| 91成人精品国语自产拍| 美女呻吟翘臀后进爆白浆| 美国毛片亚洲社区成人看| 怎么样操女人的逼亚洲Av黄片段|