亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

large cylinder Sold to Germany

Release time:2023-11-08 10:36:30 Hits: Current position: Home > News

This article mainly introduces:

Germany hydraulic cylinder,large cylinder manufacturer,large cylinder

Germany large cylinder

(Germany large cylinder,produced by Hengyu Hydraulic Co., Ltd)

large cylinder are widely used in Germany,because of clever hydraulic energy conversion,no transmission clearance,powerful torque.So our company has designed large cylinder for customers from Germany.

Introduction to large cylinder:

Causes and countermeasures of oil large cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the large cylinder will lead to premature wear of the piston seal, replace the piston seal; If the large cylinder is visibly scarred, the large cylinder must be replaced. It can be pressurized at one end of the large cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most large cylinder piston drift may not come from the large cylinder, the above method to determine the large cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

When the oil pressure of the large cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

large cylinder installation precautions: Before installing the large cylinder into the system, the parameters on the large cylinder label should be compared with the parameters when ordering. The base of the large cylinder must have sufficient stiffness, otherwise the large cylinder will bend upward into a bow when pressurized, so that the piston rod will bend.

The assembly work of the large cylinder has a great impact on the quality of the large cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Answers to some questions about large cylinder:

Where's the hydraulic cylinder bleed valve?
There is a vent hole at the top of the cylinder next to the intake pipe. Generally, it can be used, and the air in the cylinder can be naturally drained after several moves.

How to select swing cylinder? Under what conditions are they designed and selected?
1, determine the system parameters: ① the weight and the required force; ② Nominal working pressure and range; ③ The time required to travel this distance; 4 oil medium 2, installation method: select the appropriate way for the specific application 3, cylinder diameter and working pressure: determine the cylinder diameter and provide the necessary force required by the system pressure 4, piston rod: determine the minimum piston rod diameter required to withstand the longitudinal bending force, select the appropriate piston rod end and piston rod end thread 5, piston: Whether the seal type is suitable for the application 6, buffer: choose the buffer requirements as appropriate.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产操小骚逼视频| 色噜噜噜噜一区二区三区| 亚洲国产成人久久成人52| 骚女性爱视频在线看| 国产亚洲精品一区久久| 强奷很舒服好爽好爽| 大鸡巴干浪穴视频| 日韩午夜经典福利| 啊服慢一点插入逼逼| 亚洲精品一区二区精华液| 欧美成人3p视频| 国产欧美日本韩国一区二区| 国奴精品毛片av一区二区三区| 欧美一区二区三区色婷婷月色| 护士毛片在线看中文字幕| 亚洲av 又黄又爽十大| 伊人久久丁香色婷婷啪啪| 无码毛片一区二区本码视频| 欧美人与性动交b欧美精品| 亚洲一区二区三区四区国产| 插BB流水水视频| 搬开女人下面使劲插视频| 最新中文字幕av不卡高清| 美女亚洲福利视频| 美女被操的流水AV| 国产亚洲精品高清视频免费| 91秦先生全集在线观看| 亚洲二亚洲欧美一区vr| 少妇无码一区二区二三区| 久久久久有精品国产麻豆| 白虎鲍鱼抠逼免费看| 最新日本一区二区三区免费看| 日韩精品人妻一区二区免费| 大鸡吧干小逼逼视频大全| 精品无码一区二区三区无码| 免费黄色 操逼视频| 一区二区三区四区五六区| 午夜性刺激在线视频免费| 一级特黄大片色欧美精品| 搬开女人下面使劲插视频| 国产一区精品在线|