亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

series synchronous cylinder Sold to Panama

Release time:2023-11-26 09:49:48 Hits: Current position: Home > News

This article mainly introduces:

Panama hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

Panama series synchronous cylinder

(Panama series synchronous cylinder,produced by Hengyu Group)

series synchronous cylinder are widely used in Panama,because of no need for deceleration device,high work efficiency,excellent fatigue and impact resistance.So our company has designed series synchronous cylinder for customers from Panama.

Introduction to series synchronous cylinder:

When the series synchronous cylinder is in use, ensure that the series synchronous cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

The series synchronous cylinder should be vented: when the series synchronous cylinder is installed or parked for a long time to work again, the air will penetrate into the series synchronous cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the series synchronous cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the series synchronous cylinder, the oil is best entered and discharged from the highest point of the series synchronous cylinder. series synchronous cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

Regular maintenance of the series synchronous cylinder includes: regular tightening, series synchronous cylinder fastening screws and gland screws, series synchronous cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the series synchronous cylinder once a year. Clean regularly, the series synchronous cylinder is cleaned every other year, and the seals are replaced while cleaning.

We can not just consider the price and ignore the quality when we purchase the series synchronous cylinders. Now some manufacturers produce unqualified products in order to reduce costs, the piston rod is not adjusted, the rod coating is not enough, the series synchronous cylinder finish can not reach, the guide sleeve should use copper, but instead of ductile iron, although the cost is reduced, the quality of the series synchronous cylinder is not required.

Answers to some questions about series synchronous cylinder:

By what means can the hydraulic system control the arbitrary stroke position of the rotary cylinder piston rod?
The following ways can be considered: 1, through the limit device, such as limit switch, position sensor, etc. 2, by feedback the pressure of the hydraulic oil in the cylinder. The load determines the pressure, the pressure in the cylinder is determined by the load, and the pressure is very small when the cylinder is unloaded. 2.1 When clamping the workpiece, the pressure of the cylinder increases, by calculating the relationship between the clamping force and the pressure of the cylinder, take a pressure value of the cylinder, set the pressure switch, and drive the valve to work when the pressure reaches the preset value, so that the oil circuit stops supplying oil. 2.2 or set the pressure value of the relief valve to overflow after a certain set pressure.

Structural characteristics of the plunger cylinder? (1) The plunger hydraulic cylinder is a single-acting hydraulic cylinder, which can only move in one direction by hydraulic pressure, and the return trip of the plunger depends on other external forces or the weight of the plunger; (2) The plunger is only supported by the cylinder liner and is not in contact with the cylinder liner, so the cylinder liner is easy to process, so it is suitable for long stroke hydraulic cylinder; (3) the total pressure of the plunger during work, so it must have sufficient stiffness; (4) The weight of the plunger is often large, and it is easy to sag due to its own weight when placed horizontally, resulting in wear of the seals and guide side, so its vertical use is more favorable.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
东北女人国语对白视频| 久久久久国产精品老熟女| 欧美综合亚洲日韩精品区| 精品天堂色吊丝一区二区| 欧美日韩精品一区二区三区激情在线| 一区二区三区久久九九| 日韩一区二区三区久久久| 九色精品国产亚洲av麻豆一| 国产视频网站在线不卡| 午夜无码精品一区二区三区| 五月婷婷六月丁香免费视频| 国产精品久久久久久久久久一区| 亚洲精中文字幕二区三区| 欧美精品在欧美一区二区三区| 日本一区二区三区综合| 久久熟女av一区二区三区| 国产美女高潮抽搐流水在线看| 亚洲一区精品中文字幕| 亚洲国产日韩一区精品| 国产精品熟女高潮久久99| 操久久久久久久久久久久久久久久久| 日韩推理片电影在线播放| 国产精品熟女视频网站| av高清在线免费播放| 亚洲国产精品午夜福利久久| 国产真人实拍女处实破| 一区二区三区精品亚洲视频| 亚洲一道本中文字幕一区二区| 国内精品久久久久久久久久久| 91精品国自产在线播放| 国产精品亚洲欧美日韩一区在线| 亚洲国产精品无码久久久高潮| 久久综合视频三级黄片| 久久精品国产成人午夜福利| av高清在线免费播放| 人人妻人人澡av天堂香蕉| 久久久久久国产综合精品| 在线精品国产一区二区三区| 日韩精品一区二区亚洲v欧美v日韩| 久久中文字幕人妻熟| 久久免费少妇高潮视频|