亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stern plate hydraulic cylinder Sold to Nigeria

Release time:2023-11-08 10:36:23 Hits: Current position: Home > News

This article mainly introduces:

Nigeria hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

Nigeria stern plate hydraulic cylinder

(Nigeria stern plate hydraulic cylinder,produced by Hebei Hengyu company)

stern plate hydraulic cylinder are widely used in Nigeria,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed stern plate hydraulic cylinder for customers from Nigeria.

Introduction to stern plate hydraulic cylinder:

If air enters the hydraulic system, the stern plate hydraulic cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

If the stern plate hydraulic cylinder slips or crawls, please check whether there is astringency inside the stern plate hydraulic cylinder, because the internal parts of the stern plate hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the stern plate hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the stern plate hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

The material, shape and compression of the stern plate hydraulic cylinder seal have a great impact on the service life and work efficiency of the stern plate hydraulic cylinder. In addition to requiring a reliable seal, it should also have a long service life and less friction loss. At present, there are many seal manufacturers in the country, and it is also crucial to choose high-quality seals with reliable and stable quality.

The wear of the hard chromium plating layer of the stern plate hydraulic cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

Answers to some questions about stern plate hydraulic cylinder:

How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.

By what means can the hydraulic system control the arbitrary stroke position of the rotary cylinder piston rod?
The following ways can be considered: 1, through the limit device, such as limit switch, position sensor, etc. 2, by feedback the pressure of the hydraulic oil in the cylinder. The load determines the pressure, the pressure in the cylinder is determined by the load, and the pressure is very small when the cylinder is unloaded. 2.1 When clamping the workpiece, the pressure of the cylinder increases, by calculating the relationship between the clamping force and the pressure of the cylinder, take a pressure value of the cylinder, set the pressure switch, and drive the valve to work when the pressure reaches the preset value, so that the oil circuit stops supplying oil. 2.2 or set the pressure value of the relief valve to overflow after a certain set pressure.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品人妻少妇一区二区三区不卡| 美女被插进去黄色| 欧美日韩视频在线一区二区| 成人av大全免费一区二区三区| 最新免费高清无码片| 国产乱理伦片在线观看夜| 顶的速度越来越快越| 女人被男人操到高潮视频| 欧美真人性爱视频| 日韩aaa成人免费观看| 日本高清一区二区三区水蜜桃| 日韩激情视频在线看免费| 国产试看精品无码中| 国产午夜高清无码一级片| 欧美国产中文高高靖| 操女人逼逼骚逼逼| 白嫩在线亚洲观看| 大鸡吧小骚逼视频| —级v免费大片欧美| 久久久久久久久中文字幕| 精品精品视频国产| 美性中文网中文字幕91| 亚洲一区二区三区日本在线| 国产精品视频美熟女一区二区| 国产一区二区三区在线观| 欧美国产三级片久久高清| A级毛片高清视频| 影音先锋亚洲中文综合网| 亚洲男性天堂一区二区三区| 大胸瑟瑟黑丝午夜| 国产高清一区二区三区四区色| 欧美 日韩 亚洲 熟女| 国产91视频观看| 人妻波多野结衣爽到喷水| 很黄很爽的免费视频大全| 日逼动态视频免费看| 美女日比视频播放| 中文国产成人精品久久久| 亚洲另类激情在线观看| 女人被男人操到高潮视频| 欧美 日韩 国产 自拍|