亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

non-standard special type cylinder Sold to Sweden

Release time:2023-11-24 08:39:34 Hits: Current position: Home > News

This article mainly introduces:

Sweden hydraulic cylinder,non-standard special type cylinder manufacturer,non-standard special type cylinder

Sweden non-standard special type cylinder

(Sweden non-standard special type cylinder,produced by Hebei Hengyu company)

non-standard special type cylinder are widely used in Sweden,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed non-standard special type cylinder for customers from Sweden.

Introduction to non-standard special type cylinder:

Under normal circumstances, the non-standard special type cylinder is composed of the rear end cover, body, piston, piston rod and front end cover and other main parts. In order to prevent the working medium from leaking out of the non-standard special type cylinder or from the high pressure chamber to the low pressure chamber, a sealing device (sealing ring) is arranged between the non-standard special type cylinder and the end cover, the piston and the piston rod, the piston and the non-standard special type cylinder, the piston rod and the front end cover. A dustproof device is also provided on the outside of the front end cover. In order to prevent the piston from impacting the end cap when it moves rapidly to the end of the stroke, the end of the non-standard special type cylinder can also be provided with a buffer device. If necessary, the exhaust device should be set in order to exhaust.

Do not enter foreign bodies when installing the non-standard special type cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

If air enters the hydraulic system, the non-standard special type cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

If the seal of the non-standard special type cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and non-standard special type cylinder, and the phenomenon of "pulling the non-standard special type cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

Answers to some questions about non-standard special type cylinder:

How to calculate multistage cylinder volume?
When the multi-stage cylinder is extended, the largest cylinder is extended first, and when the largest cylinder stroke is completed, the second largest cylinder is extended again, the second largest cylinder stroke is completed, the third largest cylinder is extended again... Therefore, the cylinder extension length is less than the stroke of the largest cylinder, and the volume is the extension length times the inner hole area of the largest cylinder. The cylinder extension length is greater than the maximum cylinder stroke and less than (the largest cylinder stroke + the second largest cylinder stroke), and the volume is the largest cylinder stroke times the internal hole area of the largest cylinder + (the extension length - the largest cylinder stroke) times the second largest cylinder.

What should we pay attention to when using the cylinder?
When using the cylinder, we should pay attention to the environment and temperature in which it is located as follows: 1. Before working, the hydraulic cylinder must carry out several reciprocating movements under low pressure (greater than the starting pressure), and work normally after removing the gas in the cylinder. 2. Precautions when removing the hydraulic cylinder: ① The pressure in the hydraulic circuit is reduced to zero before disassembly. ② The screw thread at the top of the piston rod should be prevented from damage when disassembling. ③ Due to the different structure and size of the hydraulic cylinder, the order of disassembly is also slightly different. Generally, the fastening bolt of the end cover should be loosened first. Internal card chain card key application special tools.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大鸡巴操饿罗斯女人| 成人高清在线播放一区二区三区| 丰满少妇被强入在线观看| 女人张开腿让男人捅个爽| 国产天堂网一区二区三区 | 瓯美在线免费视频笫一区第二区| 大鸡巴日小美女明星的BB| 国产精品视频一区二区三区八戒| 中文字幕无码区一区二区| 肏亚洲女人小骚逼| 精品精品国产一区二区性色av| 伊人久久亚洲婷婷综合久久| 亚洲午夜国产片在线观看| 尤物网三级在线观看| 精品免费久久久久久久久| 韩美国男人叉女人| 日逼动态视频免费看| 欧美日韩久久久久久久久| 亚洲欧美一区二区爽爽爽| 亚洲综合区欧美一区二区| 嗯啊好大好想要视频| 美女最骚逼逼视频| 日韩一区二区三区夜色视频| 亚洲天堂成年人在线视频| 日韩视频无码日韩视频又2020| 久久久久久久久黄片观看| 一级毛片完整版免费播放一区| 大鸡巴插入阴道视频| 色偷偷影音先锋男人av| 被医生添奶头和下面好爽| 日本精品久久不卡一区二区| 国产乱子伦视频一区二区三区| 9999热精品免费视频| 女生的鸡鸡色色软件| 在线观看国产日韩欧美一区二区| 亚洲欧美日韩精品一区二区| 日韩亚洲AV无码一区二区不卡| 熟妇好大好深好爽| 女同舔我下面直流水| 另类 专区 综合 中文| 中文无码av动作片|