亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reset cylinder Sold to Mexico

Release time:2023-11-23 08:22:53 Hits: Current position: Home > News

This article mainly introduces:

Mexico hydraulic cylinder,reset cylinder manufacturer,reset cylinder

Mexico reset cylinder

(Mexico reset cylinder,produced by Hengyu Hydraulic Co., Ltd)

reset cylinder are widely used in Mexico,because of no need for deceleration device,smooth movement,long service life.So our company has designed reset cylinder for customers from Mexico.

Introduction to reset cylinder:

reset cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the reset cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

The commonly used buffer structure of the reset cylinder is composed of a piston boss and a reset cylinder head groove. When the piston moves close to the reset cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

When the reset cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the reset cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

The difference between the plunger reset cylinder and the piston reset cylinder is that the piston in the reset cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type reset cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

Answers to some questions about reset cylinder:

What are the functions of hydraulic cylinders?
Hydraulic cylinder is a hydraulic actuator, the specific role depends on the installation occasion and the type of hydraulic cylinder. Hydraulic cylinder is mainly used in machinery, and it is the most important component of construction machinery. It is important core component which mainly provide power for machinery.

Why the cylinder cannot operate normally after the explosion-proof valve is installed?
The pipeline explosion-proof valve is specially designed to prevent pipeline damage and free fall of the cylinder, so there must be back pressure to open. If there is no oil return pressure, or the oil return pressure is too small, and can not adjust the oil return pressure, such a system with explosion-proof valves is more troublesome, it is recommended to add a one-way throttle valve between the cylinder and the tank to establish back pressure. If you understand the explosion-proof valve, you can also try to adjust the opening of the valve (that is, the flow of the regulating valve), and adjust the opening to help the valve to open.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩午夜免费av在线| 日韩午夜经典福利| 非洲大鸡巴操逼黄色录像| 美国毛片亚洲社区成人看| 怎么样操女人的逼亚洲Av黄片段| 无码av一区二区大桥久未| 日韩久久中文字幕| 中文字幕乱码一区三区免费| 少妇精品久久久一区二区免费| 中文字幕人妻一区二区三区人妻| 中文字幕人妻一区二区三区久久| av中文字幕一区二区精品久久| 日韩一区二区三区夜色视频| 哈啊慢点不要了视频| 差鸡巴没码在线观看| 操纯欲女生小穴视频| 国产天美传媒剧免费观看| 尤物网三级在线观看| 丁香婷婷色婷婷粗大| 欧美大鸡巴爆草美女| 啊啊啊别操了视频| 美女爽的嗷嗷叫免费| 无码毛片一区二区本码视频| 欧美人与兽大屌肛交爆菊| 成人黄色网破处在线播放| 中文字幕在线视频一区二区| 欧美性爱撅臀插入啪啪啪| 大肉棒插了按摩视频| 女人扒开腿让我舔十八禁| 一区二区三区中文欧美| 性色av一区二区三区天美传媒四| 激情五月六月婷婷俺来也| 国产精品538一区二区在线| 中文字幕一区二区日韩精品蜜臂| 亚洲欧美日韩清纯唯美第一区| 骚女性爱视频在线看| 中文字幕在线资源第一页| 亚洲 欧美 精品 高清| 老色鬼精品视频二区三区| 国产午夜久久精品一区四虎| 99爱这里只有精品|