亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to Ireland

Release time:2023-11-08 08:12:19 Hits: Current position: Home > News

This article mainly introduces:

Ireland hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

Ireland tilting furnace hydraulic cylinder

(Ireland tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tilting furnace hydraulic cylinder are widely used in Ireland,because of no need for deceleration device,long service life,smooth movement.So our company has designed tilting furnace hydraulic cylinder for customers from Ireland.

Introduction to tilting furnace hydraulic cylinder:

Piston tilting furnace hydraulic cylinder is widely used in hydraulic transmission. When the tilting furnace hydraulic cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the tilting furnace hydraulic cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the tilting furnace hydraulic cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

When the tilting furnace hydraulic cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the tilting furnace hydraulic cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the tilting furnace hydraulic cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the tilting furnace hydraulic cylinder can meet the requirements by grinding. However, the life and reliability of this repair tilting furnace hydraulic cylinder are not high.

The method of sleeve tilting furnace hydraulic cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the tilting furnace hydraulic cylinder can be significantly improved by rolling in the finishing of the inner holes of the tilting furnace hydraulic cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

If the seal of the tilting furnace hydraulic cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

Answers to some questions about tilting furnace hydraulic cylinder:

How to remove the air in hydraulic cylinder?
Connected the cylinder to the system, and reciprocating move with full stroke several times, then the air can be eliminated . There is also a clunky method as follows: first remove the rod cavity oil pipe, connect the rodless cavity oil circuit to extend all the cylinders, and then remove the rodless cavity oil pipe, connect the rod cavity oil pipe and withdraw all the cylinders, and then connect the rodless cavity oil pipe, so that there is no air in the cylinder.

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
大阴茎交于大阴户黄片视频| 欧美一区二区三区男人的天堂| 插插插插插插插插插插插| 久久精品欧美精品免费观看| 大男人在线无码直播| 九九热在线精品免费看| 高颜值情侣鸡巴插插淫叫| 老熟妇高潮一区二区高清视频| 久久精品国产亚洲高清| 亚洲欧美国产原创一区二区三区| 美女穿黑丝被大鸡巴猛操| 国精品午夜福利视频导航| 欧美综合区自拍亚洲综合| 鸡巴抽插逼逼视频| 插到底啊啊啊视频| 日韩av一区二区三区激情在线| 女女同性女同1区二区三| 被公侵犯人妻少妇一区二区三区| 久久精品一区二区三区免费看| 国产一区曰韩二区欧美三区| 欧美性做爰片免费视频看| 日韩午夜免费av在线| 操小骚逼高潮视频| 黑人大屌大战中国女| 怎么样操女人的逼亚洲Av黄片段| 人妻少妇精品视频12p| 粉色av一区二区三区| 快速了解国产一级a爱片| 美女张开腿让男人桶91| 韩国精品视频一区二区在线观看| 亚洲欧美日韩清纯唯美第一区| 国产一区二区三区午夜精品久久| 亚洲AV无码一区二区三区系列| 在线12萝自慰喷水| 爱男爽高潮鸡穴视频| 国产亂倫近親相姦| 国产精品自在自线。| 欧美日本大白屁股大黑逼操逼视频| 啊啊啊别操了视频| 国产在线中文字幕一区二区三区| 999精品免费视频|